{"product_id":"b9361-hima-rack-power-supply-new-original-stock","title":"B9361 HIMA Rack Power Supply | New \u0026 Original Stock","description":"\u003ch2\u003eHIMA B9361 HIQuad\/HIMax Series Power Supply Module\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eHIMA B9361\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eB9361\u003c\/strong\u003e Safety Power Supply Module, serves as the primary \u003cstrong\u003eB9361\u003c\/strong\u003e Power Supply Module utilized to execute regulated DC power distribution across HIQuad\/HIMax Series platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eB9361 (Alternate Part No: 997009361)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eHIMA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eGermany\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eModule Type\u003c\/td\u003e\n\u003ctd\u003eRedundant Power Supply Module\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput Voltage Range\u003c\/td\u003e\n\u003ctd\u003e110-230 VAC, 50\/60 Hz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Voltage\u003c\/td\u003e\n\u003ctd\u003e24 VDC regulated (up to 10 A) or 5 VDC (up to 18 A)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRedundancy\u003c\/td\u003e\n\u003ctd\u003eN+1 or Triple-Module Redundant (TMR) topologies\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eResponse Time\u003c\/td\u003e\n\u003ctd\u003e\u0026lt; 10 ms\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-25 to +70 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eVaries by output load factor (Max load capacity dependent)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e221 x 482 x 300 mm (Rack-mount variant configuration)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e3.2 kg (8.00 lbs packaged assembly)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eTriple Modular Redundancy and Fail-Safe State Execution\u003c\/h3\u003e\n\u003cp\u003eThe B9361 engineering framework features integral coupling matrices that support triple modular redundancy (TMR) 2oo3 architecture options when populated within dedicated HIMA backplane enclosures. Internal voting circuits continually assess current shared performance across parallel power rails, enabling automatic load-sharing transitions and sub-millisecond fault isolation. Complete galvanic isolation separates the incoming 110-230 VAC line potentials from the internal DC logic buses. If internal over-voltage tracking thresholds are breached, the hardware switches to a diagnostic fail-safe state execution, shutting down the affected output regulator loop to prevent structural electrical faults from spreading to adjacent safety processors.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: What are the restrictive parameters when performing a hot-swap replacement on the B9361 module?\u003c\/p\u003e\n\u003cp\u003eA: Hot-swapping the B9361 module is permissible only when it operates inside a valid N+1 or TMR redundant configuration where the remaining parallel power supply units can sustain the total active backplane current load. The faulty unit must be pulled straight out of its slot to prevent physical backplane pin short-circuits.\u003c\/p\u003e\n\u003cp\u003eQ: How does the B9361 communicate internal hardware faults or output voltage degradation to the master controller?\u003c\/p\u003e\n\u003cp\u003eA: The module incorporates built-in diagnostic real-time fault detection loops that interface with separate fault relay signaling contacts. When output boundaries drop or an internal diode bridge fails, the hardware state shifts, de-energizing the fault relay and toggling the front-panel indicator matrix to prompt an system alarm.\u003c\/p\u003e\n\u003cp\u003eQ: What specific hardware step is required to determine if the module drives a 24 VDC or 5 VDC subplane architecture?\u003c\/p\u003e\n\u003cp\u003eA: Output parameters are governed by factory component populating configurations matching the architecture family (HIMax versus HIQuad). Part allocation must be confirmed via the specific suffix sub-code and order scheme before seating the card into an active backplane track.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eChassis Insertion and Mechanical Retention:\u003c\/strong\u003e Slide the power supply housing along the rack guide channels until the heavy-duty input\/output blade connectors sit completely flush within the backplane socket array. Secure all front-panel retaining screws to eliminate vibration stress.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAC and DC Conductor Separation:\u003c\/strong\u003e Route incoming 110-230 VAC supply mains cables through separate, isolated metallic wireways completely divorced from low-voltage 24 VDC \/ 5 VDC distribution lines to block inductive high-frequency noise injection per IEC 61131-2.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower Wire Gauge Specifications:\u003c\/strong\u003e Utilize a minimum conductor cross-section of 1.5 mm2 for all power supply field feed terminals. Verify that all wire endings are finished with insulated crimp ferrules to avoid stray strand shorts.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThermal Clearance and Dissipation Paths:\u003c\/strong\u003e Ensure that upper, lower, and rear ventilation louvers are unobstructed. Maintain cabinet fan airflow tracking to prevent internal pocket temperatures from exceeding the maximum +70 deg C operating threshold.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"HIMA","offers":[{"title":"Default Title","offer_id":43426733981786,"sku":"B9361","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0710\/5957\/0778\/files\/280._b83d4207-9442-4b9d-8590-6de547a6d3b2.jpg?v=1779949024","url":"https:\/\/www.spareoil.com\/products\/b9361-hima-rack-power-supply-new-original-stock","provider":"SpareOil Automation","version":"1.0","type":"link"}