{"product_id":"bently-nevada-16710-30-interconnect-cable","title":"Bently Nevada 16710-30 Interconnect Cable","description":"\u003cp\u003eConfigured for signal transmission between seismic sensors and monitoring platforms, the \u003cstrong\u003eBently Nevada 16710-30\u003c\/strong\u003e (\u003cstrong\u003e16710-30\u003c\/strong\u003e Interconnect Cable) provides direct physical execution of low-level analog signal routing.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e16710-30\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e30 ft length\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eStandard industrial range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive transmission\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCompatibility\u003c\/td\u003e\n\u003ctd\u003e330400 and 330425 Accelerometers\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eMechanical Monitoring and TSI Characteristics\u003c\/h3\u003e\n\u003cp\u003eThe 16710-30 interconnect cable serves as the primary transmission medium for piezoelectric acceleration transducers. Precise rotor dynamics analysis requires signal path integrity; the cable utilizes a shielded design to assist in cross-talk suppression. Shield termination practices must ensure that the drain wire is connected to a common ground at the vibration monitor input to prevent the induction of electromagnetic noise. When deploying these cables in proximity to variable frequency drive outputs or high-voltage AC conductors, maintain maximum physical separation to avoid the injection of common-mode interference into the seismic signal stream.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the 16710-30 cable be spliced if the required length is shorter than 30 ft?\u003c\/p\u003e\n\u003cp\u003eA: Splicing is not recommended as it introduces impedance discontinuities and potential points of ingress for electromagnetic interference. If the length is excessive, coil the excess cable in a location isolated from high-energy electromagnetic fields.\u003c\/p\u003e\n\u003cp\u003eQ: Is this cable shielded against electrical noise?\u003c\/p\u003e\n\u003cp\u003eA: Yes, the internal construction includes shielding intended to reduce external interference. Correct shield termination at the terminal block of the monitoring system is required to achieve rated noise immunity.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003eInspect the cable jacket for physical damage or abrasions prior to routing through conduit or cable trays.\u003c\/li\u003e\n\u003cli\u003eMaintain a minimum bend radius to prevent internal conductor strain or degradation of the shielding effectiveness.\u003c\/li\u003e\n\u003cli\u003eSecure the cable using non-conductive cable ties to prevent vibration-induced movement and mechanical wear against metallic surfaces.\u003c\/li\u003e\n\u003cli\u003eTerminate the shield at the vibration monitor input interface according to the monitor hardware manual to establish a continuous ground path.\u003c\/li\u003e\n\u003cli\u003eAvoid routing signal cables in common conduits with high-power AC lines to prevent crosstalk and inductive coupling.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":43551822217306,"sku":"16710-30","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0710\/5957\/0778\/files\/16710-30.png?v=1782360263","url":"https:\/\/www.spareoil.com\/products\/bently-nevada-16710-30-interconnect-cable","provider":"SpareOil Automation","version":"1.0","type":"link"}