ADM51C-2 Yokogawa CENTUM Series Datasheet & Technical Manual

ADM51C-2 Yokogawa CENTUM Analog Pulse Input Module

ADM51C-2 Yokogawa CENTUM Analog Pulse Input Module

Disponibilidad: 99 Quedan en stock

Yokogawa ADM51C-2 CENTUM Input Module Configured for high-speed pulse and analog signal acquisition in CENTUM VP and Centum CS systems,...

Código: ADM51C-2

Manufacturer: Yokogawa
Product No.: ADM51C-2
Product Type: Analog Input Modules
Product Origin: JAPAN
Payment:T/T, Western Union
Weight: 100g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

Yokogawa ADM51C-2 CENTUM Input Module

Configured for high-speed pulse and analog signal acquisition in CENTUM VP and Centum CS systems, the Yokogawa ADM51C-2 (ADM51C Input Module) provides direct physical/electrical execution. The hardware reads multiple input signal variations including contact inputs, voltage pulses, and current pulses across isolated channels, converting field data into digital registers over the system bus. By implementing selectable termination resistances and sub-millisecond pulse capture limits, the module handles high-frequency tracking loops directly across the sub-rack communication network.

Hardware Specifications

Parameter	Specification
Model	ADM51C-2
Brand	Yokogawa
Origin	Japan
Weight	0.1 kg
Dimensions	25 mm x 229 mm x 76 mm
Operating Temp	0 to 50 deg C
Power Consumption	Not Specified
Product Type	Analog Input Modules
Input Channels	16 isolated channels
Input Frequency	0 to 10 kHz
Data Update Period	10 ms
Minimum Pulse Width	40 us
Input Signal Level	3 to 24 VDC voltage, current pulse (2-wire/3-wire)
Resolution	16-bit A/D conversion
Accuracy	+/-0.1% of full scale
Selectable Shunt Resistor	200 Ohm, 510 Ohm, 1000 Ohm
Auxiliary Output	Open collector transistor contact (30 VDC, 30 mA)
Withstand Voltage	500 VAC
Insulation Resistance	Minimum 100 MOhm (500 VDC)

Process Control and Signal Processing Characteristics

The hardware layout integrates physical tracking channels designed to execute the 4-20 mA HART loop protocol alongside high-frequency pulse train metrics. Internal channel-to-channel isolation networks form galvanic boundaries that limit common-mode signal noise, containing localized electrical distortions before they impact adjacent conversion chips. Integrated processing circuits run constant loop diagnostics to identify open-circuit behavior and field-side line shorts, updating internal health parameters every 10 ms to enforce deterministic tracking across the entire Field Control Station infrastructure.

Frequently Asked Questions

Q: How do the selectable internal shunt resistors modify channel execution during current pulse capture?

A: The configuration switches match the module hardware interface to the specific current requirements of the field sensor. Adjusting the internal resistance parameters changes the current-to-voltage scale factor, protecting the 16-bit conversion matrix from over-saturation spikes.

Q: What physical system protection occurs when the isolation barriers encounter an overvoltage spike?

A: The internal galvanic isolation blocks withstand up to 500 VAC of potential difference between the field wiring terminals and the logic backplane. This stops transient line surges at the input interface, preventing thermal damage from migrating into the central processor logic.

Q: What is the processing behavior when an input signal pulse drops below the 40 microsecond limit?

A: The digital filtering logic rejects pulses narrower than 40 us as transient high-frequency noise. This suppression mechanism ensures that the internal pulse counting registers track only valid sensor transitions rather than induced line interference.

Field Installation Guidelines

Chassis Ground Alignment: Lock the module securely into its assigned chassis slot, confirming that the rear grounding tabs engage directly with the clean metal frame of the rack to maintain a low-impedance path to earth.
Drain Wire Shield Matrix: Terminate all external instrument cable shield wires straight to a dedicated copper ground bus within the system cubicle. Never guide raw shield wiring through the high-density signal pin headers of the front connector.
Separation of Signal Conductors: Enclose all low-voltage pulse and current loop wiring inside separate plastic trunking pathways, keeping a minimum distance separation of 200 mm from active high-power AC distribution or motor power lines.
Connector Fastening Routine: Tighten the front-panel connector assembly using specified retention torque to prevent micro-disconnections caused by continuous structural vibration in harsh industrial operating areas.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.