SAI143-H53 Yokogawa SAI143 Datasheet & Technical Manual

SAI143-H53 Yokogawa ProSafe-RS Analog Input Module

SAI143-H53 Yokogawa ProSafe-RS Analog Input Module

Disponibilidad: 10 Quedan en stock

Yokogawa SAI143-H53 Analog Input Module Configured for 16-channel analog signal acquisition in safety instrumented networks, the Yokogawa SAI143-H53 (SAI143 Analog...

Código: SAI143-H53

Manufacturer: Yokogawa
Product No.: SAI143-H53
Product Type: Analog Input Modules
Product Origin: JAPAN
Payment:T/T, Western Union
Weight: 340g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

Yokogawa SAI143-H53 Analog Input Module

Configured for 16-channel analog signal acquisition in safety instrumented networks, the Yokogawa SAI143-H53 (SAI143 Analog Input Module) provides direct physical/electrical execution.

Suffix Breakdown & Model Matrix

Suffix Code	Designation	Technical Parameter
-H	HART Communication	Enriched instrumentation interface [Release: R1.02.00]
5	Connection / Protection Type	Form factor for pressure clamp terminal block or MIL cable; no explosion protection
3	Environmental Conformance	ISA Standard G3 conformal coating; extended temperature rating (-20 to 70 deg C)

Hardware Specifications

Parameter	Specification
Model	SAI143-H53
Brand	Yokogawa
Origin	Japan
Weight	0.34 kg
Dimensions	Standard FIO architecture card scale
Operating Temp	-20 to 70 deg C
Power Consumption	320 mA at 5 VDC system side, 550 mA at 24 VDC loop side
Input Channels	16 channels, module isolation
Signal Range	4-20 mA DC (permissible range 0-25 mA)
Input Impedance	250 Ohm (Power ON), >= 500 kOhm (Power OFF)
Measurement Accuracy	plus or minus 16 uA (within 0.05 to 23 mA spectrum)
Temperature Drift	plus or minus 16 uA per 10 deg C shift
Data Update Frequency	40 ms
Transmitter Power Supply	16.15 VDC minimum (at 20 mA), 26.4 VDC maximum (at 0 mA), 25 mA current limit
Isolation Withstand Voltage	1.5 kV AC between input signal and system for 1 minute

Process Control Communication Architecture

The hardware executes active signal filtering while enforcing physical channel-to-system isolation, isolating the backplane logic from external field line transients up to 1.5 kV AC. Integrated instrumentation circuits support the 4-20 mA HART loop protocol layer, enabling high-frequency digital telemetry modulation over the standard analog loop current without disturbing the primary process variable. The hardware platform handles bi-directional asset data transfers, allowing safety managers to query real-time diagnostics from smart transmitters directly through the FIO system bus. An onboard 2-wire transmitter power switch permits systemic configuration adjustments, executing simultaneous voltage distribution cuts across all 16 channels to safely toggle field equipment levels during automated maintenance shutdowns.

Frequently Asked Questions

Q: Does the SAI143-H53 module accept terminal block matching with the STA4D-0S1 option in dual-redundant setups? A: No. The factory specifications strictly dictate that for dual-redundant pressure clamp configurations, the STA4D-0S1 component must not be deployed due to mismatching circuit paths.

Q: How does the module handle short-circuit faults on the transmitter power supply loop? A: The card contains internal hardware current limiters. If a short-circuit fault conditions the loop, the transmitter supply caps output current at 25 mA max, protecting internal paths until the fault clears.

Field Installation Guidelines

Environmental Conformance Assurance: Verify the mounting environment stays within the -20 to 70 deg C limit, relying on the ISA G3 standard coating to shield logic surfaces from corrosion.
Terminal Insertion Methods: Secure the pressure clamp terminal block or MIL cable interface tightly to front card connectors, verifying no floating strands short adjacent pins.
Shield Termination Rules: Terminate loop shields at the dedicated chassis ground bar rather than signal common paths to keep electrical noise away from the 4-20 mA conversion circuit.
Hazardous Area Isolation: Because suffix 5 variants lack intrinsic safety barriers, you must route input lines through external barriers if field sensors sit in explosion-risk zones.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.