330104-00-05-50-11-00 Bently Nevada Displacement Sensor

330104-00-05-50-11-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe

330104-00-05-50-11-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe

Disponibilidad: 10 Quedan en stock

The Bently Nevada 330104-00-05-10-02-00, also cataloged as the 330104 Proximity Probe, operates as a dedicated hardware component for non-contacting displacement...

Código: 330104-00-05-50-11-00

Manufacturer: Bently Nevada
Product No.: 330104-00-05-50-11-00
Product Type: Proximity Sensors
Product Origin: USA
Payment:T/T, Western Union
Weight: 2000g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

The Bently Nevada 330104-00-05-10-02-00, also cataloged as the 330104 Proximity Probe, operates as a dedicated hardware component for non-contacting displacement measurement within the 3300 XL 8 mm Proximity Transducer System. The component tracks dynamic shaft movement and static position parameters by monitoring eddy current variations relative to a conductive target material, transmitting high-frequency analog signals directly to a designated Proximitor Sensor.

Suffix Breakdown & Model Matrix

Code	Option Category	Technical Configuration
330104	Base Model	3300 XL 8 mm Proximity Probe (M10 x 1 Metric Thread)
00	Unthreaded Length	0 mm (Fully threaded case)
05	Overall Case Length	50 mm
50	Total Length	5.0 Metres (16.4 feet)
11	Connector/Cable	ClickLoc connector with connector protector and armor
00	Agency Approval	Not required / Standard

Hardware Specifications

Parameter	Specification
Model	330104-00-05-50-11-00
Brand	Bently Nevada
Origin	U.S.A.
Probe Tip Diameter	8.0 mm
Linear Range	2.0 mm (80 mils)
Nominal Scale Factor	7.87 V/mm (200 mV/mil)
Cable Impedance	75 Ohm nominal
Tip Material	Polyphenylene sulfide (PPS)
Armor Material	Flexible Stainless Steel (SST)
Operating Temp	-51 to +177 deg C
Power Consumption	Determined by external Proximitor loop
Dimensions	M10 x 1 thread, 50 mm case length, 5.0 m total length
Weight	2.0 kg (Shipping weight)

Eddy-Current Probe Scaling & Calibration

The system relies on calibrated eddy-current probe scaling to ensure linear response over the entire 2.0 mm detection range. During deployment, a critical gap voltage validation must be executed; setting the initial physical proximity to establish a -10 VDC target voltage centers the output within the linear spectrum. This precise geometric placement stabilizes the loop against rotor dynamics fluctuations and establishes the required boundary conditions for internal cross-talk suppression when adjacent probes are arrayed in close radial proximity on the same machine plane.

Frequently Asked Questions

Q: Can this 5.0-meter probe be coupled with a standard extension cable?

A: No. This probe features a total length of 5.0 metres and must interface directly with a 5.0-meter Proximitor Sensor without intermediate extension cabling. Adding an extension cable alters the 75 Ohm loop impedance and invalidates the nominal scale factor calibration.

Q: What specific ingress protection does the Option 11 connector protector provide?

A: The factory-installed connector protector provides physical and chemical isolation for the gold-plated ClickLoc interface against splash oils, moisture, and particulate matter typical of bearing housings. It does not support permanent fluid submersion.

Q: What targets are compatible with the factory-calibrated scale factor?

A: The standard scale factor of 7.87 V/mm assumes an AISI 4140 electric steel target. Using alternative target materials with different magnetic permeabilities or electrical conductivities requires recalibration of the receiver loop.

Field Installation Guidelines

Torque Limitations: When mounting the M10 x 1 threaded housing into the machine port, do not exceed the structural limit of 33.9 N-m (300 in-lb) to prevent distortion of the probe tip or casing.
Armor and Cable Routing: Maintain a minimum bend radius of 25.4 mm (1.0 inch) along the flexible stainless steel armor to avoid crimping or fracturing the internal 75 Ohm coaxial core.
Isolation and Grounding: The coaxial outer shield must maintain insulation from the machine case ground along the entire run. Grounding must terminate strictly at the Proximitor Sensor end within the designated instrument enclosure.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.