330930-040-00-00 Bently Nevada Extension Cable

330930-040-00-00 3300 XL Standard Extension Cable | Bently Nevada

330930-040-00-00 3300 XL Standard Extension Cable | Bently Nevada

Disponibilidad: 10 Quedan en stock

The Bently Nevada 330930-040-00-00, also cataloged as the 3300 XL Standard Extension Cable, operates as a dedicated hardware component for...

Código: 330930-040-00-00

Manufacturer: Bently Nevada
Product No.: 330930-040-00-00
Product Type: Proximity Sensors
Product Origin: USA
Payment:T/T, Western Union
Weight: 2000g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

The Bently Nevada 330930-040-00-00, also cataloged as the 3300 XL Standard Extension Cable, operates as a dedicated hardware component for high-frequency signal transmission between proximity probes and Proximitor sensors within 3300 XL Transducer System networks.

Suffix Breakdown & Model Matrix

The part number structure defines the physical length, protective armoring, and agency approval options for the extension cable assembly:

330930: Base Model for 3300 XL Standard Extension Cable
040: Cable Length Option - 4.0 meters (13.1 feet)
00: Connector and Cable Option - Without stainless steel armor
00: Agency Approval Option - Not required

Hardware Specifications

Parameter	Specification
Model	330930-040-00-00
Brand	Bently Nevada
Origin	USA
Weight	2.0 kg
Dimensions	4.0 meters (13.1 feet) length
Operating Temp	-51 to 177 deg C (-60 to 350 deg F)
Power Consumption	Passive physical conductor (zero power dissipation)
Cable Type	Standard coaxial extension cable
Connector Type	ClickLoc miniature coaxial connectors
Stainless Steel Armor	Option 00 (Without stainless steel armor)
Agency Approval	Option 00 (Not required)

Rotor Dynamics & Gap Voltage Validation

The 3300 XL extension cable transmits raw radio-frequency signals between the proximity probe and the Proximitor sensor, maintaining matched impedance across the transducer circuit. Correct total system length (combining probe cable and extension cable to match 5-meter or 9-meter sensor tuning) is critical for precise eddy-current probe scaling and rotor dynamics monitoring. Field commissioning requires verifying the physical probe clearance via gap voltage validation, ensuring the Proximitor output delivers a nominal -10 VDC baseline target under static shaft conditions before dynamic signal logging.

Frequently Asked Questions

Q: How does total cable length impact signal calibration in the 3300 XL proximity system?

A: The Proximitor sensor is factory-calibrated to a specific total circuit length (5.0 m or 9.0 m). Deviating from the specified extension cable length shifts system capacitance and compromises linear sensitivity calibration.

Q: What connector maintenance is required for ClickLoc coaxial fittings during field installation?

A: Connectors must remain free of oil, moisture, and conductive debris. Hand-tighten until the ClickLoc mechanism fully latches, and apply silicone sealing tape or protective boots where liquid exposure is present.

Field Installation Guidelines

Routing Path: Route the 4.0-meter extension cable through dedicated instrument conduit or cable trays away from high-voltage motor power leads to avoid electrical noise coupling.
Minimum Bend Radius: Observe a strict minimum bend radius during installation to prevent deformation of the inner coaxial dielectric layer.
Connector Mating: Inspect the ClickLoc miniature coaxial connectors for contamination before joining. Push and twist until positive mechanical latching is achieved.
Shield Grounding: Ensure proper isolation of cable shields along the run, grounding the overall shield solely at the monitor panel terminal block to eliminate ground loop interference.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.