IC698CRE030 GE Central Processing Unit

GE IC698CRE030 Rx7i PACsystems Central Processing Unit

GE IC698CRE030 Rx7i PACsystems Central Processing Unit

Disponibilidad: 10 Quedan en stock

The GE IC698CRE030, also cataloged as the IC698CRE030 Central Processing Unit, serves as the primary IC698CRE030 Central Processing Unit utilized...

Código: IC698CRE030

Manufacturer: GE Fanuc
Product No.: IC698CRE030
Product Type: Central Processing Units
Product Origin: USA
Payment:T/T, Western Union
Weight: 1330g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

The GE IC698CRE030, also cataloged as the IC698CRE030 Central Processing Unit, serves as the primary IC698CRE030 Central Processing Unit utilized to execute boolean logic and network routing across Rx7i PACsystems platforms. The module operates at 600 MHz and executes hardware-level control cycles over dual integrated serial lines and a self-negotiating Ethernet interface.

Hardware Specifications

Parameter	Specification
Model	IC698CRE030
Brand	GE Fanuc Emerson
Origin	USA
Weight	1.33 kg (2.94 lbs)
Dimensions	Standard Rx7i slot width
Operating Temp	0 to 50 deg C
Power Consumption	16.0 W (3.2 A @ 5 VDC)
Processor Speed	600 MHz
User Memory	64 MB
Discrete I/O Capacity	32 Kbits
Boolean Execution Speed	0.069 ms
Communication Interfaces	1x RJ45 Ethernet (10/100 Mbps), 1x RS-232, 1x RS-485
Protocol Support	Modbus RTU Slave, SNP, Serial I/O
Redundancy Architecture	Hot Standby Redundancy

Industrial Control and Network Determinism

The IC698CRE030 implements dedicated backplane bus communication velocity protocols to maintain deterministic I/O density scaling across the Rx7i rack layout. Embedded firmware flash compatibility enables simultaneous execution of high-speed Boolean calculation loops and Ethernet/IP or Profinet industrial network data prioritization. The underlying bus interface architecture ensures that critical application memory regions remain highly synchronized, minimizing internal transport jitter during high-density I/O scanning phases.

Frequently Asked Questions

Q: What are the restrictions regarding hot-swapping the IC698CRE030 CPU within the Rx7i backplane?

A: The IC698CRE030 must not be inserted or removed while the VME backplane power is active. Prior to module extraction or insertion, the rack power supply must be completely isolated to prevent catastrophic electrical damage to the logic circuitry and backplane connectors.

Q: How is the synchronization delay managed during a Hot Standby Redundancy failover event?

A: The hardware architecture relies on deterministic memory-mirroring processes across the redundant pair. The dedicated transfer channel handles the 64 MB memory profile synchronization, allowing bumpless switchover execution within standard control cycle parameters if the primary unit drops its heartbeat signals.

Field Installation Guidelines

Chassis Placement and Power Limits: Ensure the Rx7i chassis power supply is rated to support the 3.2 A current draw at 5 VDC required exclusively by this CPU module, alongside any additional I/O modules on the same local bus segment.
Shielding and Noise Suppression: All communication lines, including the RS-232, RS-485, and RJ45 Ethernet links, must utilize high-quality shielded twisted-pair (STP) cabling. Ground the cable shields directly to the enclosure master ground bar to eliminate common-mode electromagnetic interference.
Thermal Management: Maintain free air convection clearance zones above and below the chassis assembly. Ensure ambient enclosure internal temperatures do not exceed the 50 deg C operational limit under continuous 100% processing load.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.