IC693PWR321 GE Series 90-30 Standard Power Supply Module

Disponibilidad: 10 Quedan en stock

The GE IC693PWR321, also cataloged as the IC693PWR321 Standard Power Supply, operates as a dedicated hardware component for converting line...

Código: IC693PWR321

Manufacturer: GE Fanuc
Product No.: IC693PWR321
Product Type: PLC Power Supplies
Product Origin: USA
Payment:T/T, Western Union
Weight: 350g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

The GE IC693PWR321, also cataloged as the IC693PWR321 Standard Power Supply, operates as a dedicated hardware component for converting line input power into regulated internal operating voltages within Series 90-30 PLC platforms.

Hardware Specifications

Parameter	Specification
Model	IC693PWR321
Brand	GE Fanuc / Emerson
Origin	Factory standard
Weight	0.51 kg (1.13 lbs)
Dimensions	Single-slot wide (Occupies leftmost dedicated baseplate slot)
Operating Temp	0 to 60 deg C (Standard industrial environment)
Power Consumption	Input requirement: 90 VA (AC input) / 50 W (DC input)
Nominal Rated Voltage	120 / 240 VAC or 125 VDC
Input Voltage Range, AC	85 to 264 VAC
Input Voltage Range, DC	100 to 300 VDC
Total Output Power Rating	30 W maximum
5 VDC Output Capacity	5.0 to 5.2 VDC (5.1 VDC nominal); 15 W maximum
24 VDC Relay Output Capacity	24 to 28 VDC; 15 W maximum
24 VDC Isolated Output Capacity	21.5 to 28 VDC; 20 W maximum
Inrush Current	4 A peak, 250 ms maximum
Holdup Time	20 ms minimum
Overvoltage Protection	6.4 to 7.0 VDC (on 5 VDC rail)
Overcurrent Protection	4.0 A maximum short-circuit current limit
Communication Interface	1 x 9-pin sub-D connector (RS-485 serial protocol)
Internal Fuse Reference	GE 44A724627-109 / Bussmann GDC-2 / Littelfuse 239-002

Backplane Bus Power Distribution and I/O Density Scaling

The module installs exclusively into the leftmost slot of the Series 90-30 baseplate to directly drive the internal parallel power rails. It splits its 30 W total output across three specialized internal circuits to allow for robust I/O density scaling without inducing voltage sag. The 5 VDC rail supports local CPU logic processing, while the 24 VDC relay power rail energizes discrete output coil modules. An independent 24 VDC isolated rail supplies external power to select analog or communication modules, maintaining power separation across the deterministic backplane network.

Frequently Asked Questions

Q: What is the electrical behavior of the power supply during a direct short circuit on the field side?

A: The module contains an internal power supply limiting feature that initiates overcurrent protection when current demands reach a maximum of 4.0 A. This automatically limits output power to safeguard the internal backplane components immediately upon detection of a direct short.

Q: Can this power supply module be hot-swapped while the primary line voltage is active?

A: No. The physical design and electrical architecture of the Series 90-30 baseplate require total isolation of input line power and external loops prior to extracting or inserting the power supply unit.

Q: What is the significance of the holdup time specification for this module?

A: The minimum holdup time is 20 ms. This guarantees that the power supply will maintain regulated DC output voltages during brief line power interruptions up to 20 ms, preventing immediate CPU halts or data drops during transient power fluctuations.

Field Installation Guidelines

Disconnect all primary AC or DC input power sources and isolate any external loop voltages before executing installation or fuse replacement steps.
Insert the power supply module into the dedicated leftmost slot of the baseplate, ensuring the top and bottom chassis tabs line up exactly with the module housing guides.
Press firmly until the retention hooks click over the chassis edge to secure the unit against mechanical vibration.
Connect line input wires to the designated terminal strip using the appropriate positions for AC (Line, Neutral, Ground) or DC inputs.
Confirm that the internal backup battery is connected to its mating terminal to maintain CPU retentive memory registers during unpowered states.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.