IC200ALG264 GE Fanuc Analog Input Module

GE Fanuc IC200ALG264 VersaMax Analog Input Module

GE Fanuc IC200ALG264 VersaMax Analog Input Module

Disponibilidad: 10 Quedan en stock

The GE Fanuc IC200ALG264, also cataloged as the IC200ALG264 15-Point Analog Current Input Module, operates as a dedicated hardware component...

Código: IC200ALG264

Manufacturer: GE Fanuc
Product No.: IC200ALG264
Product Type: Analog Input Modules
Product Origin: USA
Payment:T/T, Western Union
Weight: 230g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

The GE Fanuc IC200ALG264, also cataloged as the IC200ALG264 15-Point Analog Current Input Module, operates as a dedicated hardware component for single-ended current signal acquisition within VersaMax I/O platforms. The module processes 15 analog current channels configured in a single group, converting 0-20 mA or 4-20 mA signals into 15-bit digital values for backplane transmission to the main CPU.

Hardware Specifications

Parameter	Specification
Model	IC200ALG264
Brand	GE Fanuc
Origin	USA
Weight	0.50 lbs (0.23 kg)
Dimensions	Single slot VersaMax footprint
Operating Temp	0 deg C to 60 deg C
Power Consumption	100 mA maximum at 5 VDC from PLC backplane
Number of Channels	15 single-ended inputs (1 group)
Analog Resolution	15 bits
Input Ranges	0-20 mA, 4-20 mA
Digital Resolution	0.5 uA (4-20 mA), 0.625 uA (0-20 mA)
Input Impedance	100 Ohms
Filter Response	24 Hz +/-20% (3dB corner frequency)
Update Rate	7.5 ms maximum
Isolation	250 VAC continuous, 1500 VAC for 1 minute
Diagnostic Features	Loss of internal power, open wire detection (4-20 mA mode)

Backplane Bus Communication Velocity & Firmware Flash Compatibility

The module executes high-speed serial data exchanges over the VersaMax backplane bus, completing full 15-channel data updates within a maximum cycle time of 7.5 ms. Field signals pass through dedicated Analog-to-Digital Converter (ADC) circuits with hardware 24 Hz low-pass filtering, suppressing ambient electrical transients before writing 15-bit digital outputs directly to CPU memory tables. Range execution operates via terminal hardware jumpers; removing the jumper selects default 4-20 mA processing, while installing the jumper configures 0-20 mA operation without requiring firmware re-flashing.

Frequently Asked Questions

Q: How is the input range switched between 4-20 mA and 0-20 mA?

A: Signal range selection is determined physically by the terminal jumper configuration. Leaving the terminal jumper uninstalled configures 4-20 mA operation, whereas installing the jumper sets the module to 0-20 mA operation.

Q: Does open wire diagnostic detection function in both signal range modes?

A: No, open wire detection is active only when operating in the 4-20 mA mode. Loss of internal power diagnostics remains active in both operating modes.

Q: Is channel-to-channel isolation provided on the 15 input channels?

A: No, all 15 single-ended channels belong to a single common group and share the same return potential, providing group isolation of 250 VAC continuous to the backplane, but no isolation between individual channels.

Field Installation Guidelines

Mount the module chassis firmly onto a standard DIN rail or panel plate within the VersaMax rack alignment.
Ensure system power is disconnected before seating the module into its corresponding terminal carrier interface.
Wire field transmitters to the 15 single-ended channel terminals, ensuring sensor power supplies match loop compliance requirements.
Set hardware jumpers on the terminal block base according to the targeted input signal format (uninstalled for 4-20 mA, installed for 0-20 mA).
Terminate input cable shields at a dedicated system grounding bar to maintain noise immunity and backplane signal integrity.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.