IC200ALG620 GE Fanuc RTD Input Module

IC200ALG620 | GE Fanuc | VersaMax Analog Input Module

IC200ALG620 | GE Fanuc | VersaMax Analog Input Module

Disponibilidad: 10 Quedan en stock

Configured for high-precision temperature measurement and resistance signal conversion in VersaMax system platforms, the GE Fanuc IC200ALG620 (IC200ALG620 Analog Input...

Código: IC200ALG620

Manufacturer: GE Fanuc
Product No.: IC200ALG620
Product Type: Analog Input Modules
Product Origin: USA
Payment:T/T, Western Union
Weight: 400g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

Configured for high-precision temperature measurement and resistance signal conversion in VersaMax system platforms, the GE Fanuc IC200ALG620 (IC200ALG620 Analog Input Module) provides direct physical/electrical execution. The module accommodates 4 RTD/resistance input channels utilizing dedicated 16-bit Analog-to-Digital Converters (ADCs) per channel to interface 3-wire and 4-wire RTD sensors or direct resistance ranges.

Hardware Specifications

Parameter	Specification
Model	IC200ALG620
Brand	GE Fanuc
Origin	USA
Weight	0.88 lbs (0.40 kg)
Dimensions	Single-slot VersaMax module footprint
Operating Temp	0 deg C to 60 deg C
Power Consumption	125 mA max at 5 VDC bus; 125 mA at 3.3 VDC bus
Input Channels	4-point RTD / Resistance input channels
Resolution	16 bits (15 bits plus sign)
Compatible RTD Types	Platinum (25, 100, 1000 ohm); Copper (10, 50, 100 ohm); Nickel (100, 120 ohm); Nickel/Iron (604 ohm)
Resistance Input Ranges	0-500 Ohms; 0-3000 Ohms
Wiring Configurations	3-wire and 4-wire RTDs
Maximum Lead Resistance	5 Ohms per lead
Channel Update Rate	210 ms at 60 Hz; 230 ms at 50 Hz
Measurement Accuracy	+/-0.15% on resistance; +/-0.15% on RTD temperature (at 25 deg C)
Temperature Sensitivity	+/-0.004% of reading; +/-1.5 uV per deg C (referred to input)
Isolation	250 VAC (input to logic), 1500 VAC for 1 minute (input to frame)
Status Indicators	FLD PWR LED, OK LED

Backplane Bus Communication Velocity & Firmware Flash Compatibility

The module executes internal data transfers over the VersaMax 5 VDC and 3.3 VDC logic backplane bus, drawing up to 125 mA from both supply rails. Digital conversion values are generated at a channel update rate of 210 ms at 60 Hz filter frequency or 230 ms at 50 Hz filter frequency. Onboard diagnostic firmware continuously reports channel-level conditions—including Open RTD, input short, underrange, overrange, non-volatile memory storage fault, wiring fault, and high/low alarms—directly to the host CPU controller. Front panel LED indicators signal module boot cycles, firmware updates, normal operation, and fault states.

Frequently Asked Questions

Q: What RTD wiring configurations are supported by the IC200ALG620?

A: The module directly supports both 3-wire and 4-wire RTD sensor wiring arrangements with a maximum allowable lead resistance of 5 Ohms per lead.

Q: How does the OK LED report operational and diagnostic states?

A: A solid green OK LED indicates normal backplane power and operation, flashing green indicates firmware update or boot mode, and solid amber indicates an active module diagnostic error.

Q: What are the backplane current draw demands for this module?

A: The module draws a maximum of 125 mA at 5 VDC output and 125 mA at 3.3 VDC output from the system backplane.

Field Installation Guidelines

Mount the module firmly into its designated VersaMax carrier slot prior to connecting sensor field wiring.
Ensure system backplane power is off before seating or removing the module.
Route 3-wire or 4-wire RTD field cables using twisted, shielded wiring to minimize external electromagnetic interference.
Maintain lead balance across RTD connections and confirm lead resistance does not exceed 5 Ohms per lead.
Ground signal cable shields to the cabinet ground bar or carrier shield connection.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.