IC693MDL730 GE Series 90-30 Output Module

IC693MDL730 GE Series 90-30 Discrete Output Module

IC693MDL730 GE Series 90-30 Discrete Output Module

Disponibilidad: 10 Quedan en stock

The GE IC693MDL730 serves as the primary IC693MDL730 Discrete Output Module utilized to execute digital switching commands across Series 90-30...

Código: IC693MDL730

Manufacturer: GE Fanuc
Product No.: IC693MDL730
Product Type: Digital I/O Cards
Product Origin: USA
Payment:T/T, Western Union
Weight: 340g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

The GE IC693MDL730 serves as the primary IC693MDL730 Discrete Output Module utilized to execute digital switching commands across Series 90-30 platforms. The single-slot component provides high-current sourcing transistor outputs, translating central backplane logic commands into isolated physical voltage states to drive motor starters, solenoids, and field indicators.

Hardware Specifications

Parameter	Specification
Model	IC693MDL730
Brand	GE Fanuc Emerson
Origin	USA
Weight	0.34 kg (0.75 lbs)
Dimensions	Single-slot baseplate profile
Operating Temp	0 to 60 deg C
Power Consumption	55 mA @ 5 VDC (backplane bus draw, all outputs active)
Output Type	Transistor (Positive Logic/Sourcing)
Number of Points	8 channels (Single shared common group)
Nominal Output Voltage	12 / 24 VDC
Output Voltage Range	12 to 24 VDC (+20%, -15% ripple limit)
Load Current per Point	2.0 A maximum
Total Fuse Rating	2.0 A @ 60 deg C; 4.0 A @ 50 deg C
Maximum Inrush Current	9.4 A for 10 ms
Maximum Voltage Drop	1.2 VDC in ON state
Off-State Leakage	1 mA maximum
Signal Switching Delay	2 ms maximum (On and Off transitions)
Galvanic Isolation	1500 V field side to logic side baseline
Physical Interface	Removable 20-screw terminal block assembly

Industrial Control and Network Determinism

The IC693MDL730 operates via direct hardware mapping to execute binary state changes without affecting overall backplane bus communication velocity parameters. The transistor switching matrix maintains predictable execution cycles across distributed frames, enabling precise I/O density scaling profiles when mixed into 5-slot or 10-slot expansion and remote baseplates. Integrated firmware flash compatibility guarantees immediate status register tracking, allowing the CPU to monitor the front-panel blown-fuse bit, internal module fault states, and eight standalone channel LEDs without injecting bus cycle jitter.

Frequently Asked Questions

Q: Does the IC693MDL730 module draw operational power for the field-side loads directly from the backplane?

A: No. The backplane bus only supplies 55 mA at 5 VDC for the internal logic-side components. An external 12 to 24 VDC power supply must be wired to the module terminals to drive the connected physical actuators and loads.

Q: How do environmental conditions alter the overcurrent thermal protection boundaries of this unit?

A: The module internal fusing threshold degrades under thermal stress. The structural limit permits 4.0 A per fuse when ambient temperatures remain at or below 50 deg C, but limits current output down to 2.0 A per fuse when operating at the 60 deg C ceiling.

Field Installation Guidelines

Terminal Board Maintenance Handling: Ensure the rack assembly is completely unpowered before detaching or securing the 20-screw removable terminal board to prevent unintentional field voltage bridging.
Inductive Load Suppression: Install external flywheel diodes or suppression networks across all connected DC motor starters and inductive solenoids to prevent counter-EMF spikes from overriding the 1.2 VDC transistor junctions.
Chassis Slot Restrictions: Align and mount the single-slot module card into any designated I/O path within a 5-slot or 10-slot Series 90-30 baseplate. Do not install this hardware into Slot 1, which is keyed solely for the processor.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.