16925-20 Bently Nevada Interconnect Cable

16925-20 | Bently Nevada | Interconnect Cable

التوفر: 10 متوفر في المخزون

The Bently Nevada 16925-20, also cataloged as the 16925 Interconnect Cable, operates as a dedicated hardware component for signal transmission...

رمز المنتج: 16925-20

Manufacturer: Bently Nevada
Product No.: 16925-20
Product Type: Interconnect Cables
Product Origin: USA
Payment:T/T, Western Union
Weight: 250g
Shipping port: Xiamen
Warranty: 12 months

وصف التقييمات

The Bently Nevada 16925-20, also cataloged as the 16925 Interconnect Cable, operates as a dedicated hardware component for signal transmission between monitoring transducers and interface modules within machine protection networks.

Hardware Specifications

Parameter	Specification
Model	16925-20
Brand	Bently Nevada
Origin	USA
Dimensions	20 ft (6.1 m) length
Operating Temp	-40 deg C to +177 deg C (Standard)
Power Consumption	N/A (Passive component)
Cable Type	3-wire Interconnect

Rotor Dynamics and Signal Integrity

The 16925 cable assembly is designed to facilitate the high-frequency signal propagation required for accurate rotor dynamics observation. To ensure data integrity, the physical installation must prioritize the maintenance of the nominal -10 VDC gap voltage target for eddy-current probe interfaces. Any deviation in the impedance of the signal path, caused by damaged insulation or improper shield termination, can introduce artifacts into the vibration waveform. Cross-talk suppression is achieved through the integrated shielding layer; therefore, it is mandatory that the shield be terminated correctly at the instrumentation ground to prevent ground loops that interfere with phase measurement accuracy.

Frequently Asked Questions

Q: Is the 16925 cable assembly compatible with non-Bently Nevada transducers?

A: The 16925 series is factory-calibrated for specific Bently Nevada transducer interfaces. Use with third-party sensors may result in impedance mismatches, impacting the frequency response and signal-to-noise ratio of the monitoring system.

Q: What are the requirements for cable termination?

A: The assembly must be terminated in accordance with the specific monitoring module's terminal block configuration. Ensure all connections are tight to prevent resistive heating and signal fluctuation.

Field Installation Guidelines

Route the cable through dedicated instrumentation pathways, maintaining a minimum 30 cm separation from high-voltage AC lines to prevent induced noise.
Ensure the connector mating faces are clean and moisture-free before joining.
Observe a minimum bend radius of 10 times the cable diameter during installation to prevent damage to the internal conductors and shielding.
Secure the cable using non-conductive cable ties or clips at 1 m intervals to mitigate the effects of machine-induced vibration.

ماذا يقول عملاؤنا عنا؟

دعم طوارئ ممتاز!

تعطل خط إنتاجنا بسبب عطل في شاشة بنتلي نيفادا. وجدناها متوفرة لدينا في المخزون، وقاموا بشحنها إلينا عبر DHL على الفور. عاد خط الإنتاج للعمل في غضون 48 ساعة - لقد أنقذت هذه الشاشة مصنعنا حقًا.

مارك تومسون

مدير الصيانة، الولايات المتحدة الأمريكية

مصدر موثوق لقطع الغيار الجديدة

يُعدّ العثور على وحدات أصلية جديدة تمامًا أمرًا بالغ الأهمية لسلامتنا. يُقدّم هذا الفريق مكونات جديدة من المصنع مع شهادات اعتماد كاملة. والتزامهم ببيع المنتجات الجديدة فقط يجعلهم شريكنا الأكثر ثقة.

روبرت هوفمان

رئيس قسم الهندسة، ألمانيا

خدمة وجودة من الدرجة الأولى

نستورد قطع غيار هانيويل وشنايدر من هنا منذ عامين. تصل كل شحنة مغلفة بإحكام مع الحفاظ على أختام المصنع الأصلية. نتميز بالتواصل الواضح وأفضل أوقات التسليم في هذا المجال.