330104-00-07-10-02-00 Bently Nevada Proximity Probe

330104-00-07-10-02-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe

330104-00-07-10-02-00 | Bently Nevada | 3300 XL 8 mm Proximity Probe

التوفر: 10 متوفر في المخزون

The Bently Nevada 330104-00-07-10-02-00 serves as the primary 330104 Proximity Probe utilized to execute non-contacting displacement measurements across 3300 XL...

رمز المنتج: 330104-00-07-10-02-00

Manufacturer: Bently Nevada
Product No.: 330104-00-07-10-02-00
Product Type: Proximity Sensors
Product Origin: USA
Payment:T/T, Western Union
Weight: 2000g
Shipping port: Xiamen
Warranty: 12 months

وصف التقييمات

The Bently Nevada 330104-00-07-10-02-00 serves as the primary 330104 Proximity Probe utilized to execute non-contacting displacement measurements across 3300 XL Machinery Protection System platforms. The probe measures static distance variations and dynamic structural oscillations by establishing a high-frequency radio frequency field against a moving conductive target, routing raw impedance modifications along its coaxial transmission line to an external matching Proximitor Sensor.

Suffix Breakdown & Model Matrix

Code	Option Category	Technical Configuration
330104	Base Model	3300 XL 8 mm Proximity Probe (M10 x 1 Metric Thread)
00	Unthreaded Length	0 mm
07	Overall Case Length	70 mm
10	Total Length	1.0 meter (3.3 feet)
02	Connector and Cable-Type	Miniature coaxial ClickLoc connector with standard cable
00	Agency Approval	Not required

Hardware Specifications

Parameter	Specification
Model	330104-00-07-10-02-00
Brand	Bently Nevada
Origin	U.S.A.
Probe Tip Diameter	8 mm
Thread Selection	M10 x 1 metric thread
Cable Impedance	75 Ohm nominal
Operating Temp	-51 to +177 deg C
Power Consumption	Passive hardware component (driven by Proximitor excitation loop)
Dimensions	70 mm overall case length, 1.0 meter total cable length
Weight	Less than 1.0 kg nominal

Gap Voltage Validation (-10 VDC Targets)

Field integration of the 330104-00-07-10-02-00 proximity probe requires strict execution of gap voltage validation to ensure accurate rotor dynamics tracking. During manual mounting within the M10 x 1 thread interfaces, field technicians must fine-tune the mechanical distance relative to the shaft target until the steady-state DC output voltage across the Proximitor Sensor test points reads exactly -10 VDC. This baseline setup aligns the sensor within the electrical midpoint of its 2.0 mm (80 mils) linear calibration span, optimizing signal accuracy and supporting successful cross-talk suppression in high-density multi-channel probe installations.

Frequently Asked Questions

Q: Can this 1.0-meter total length probe be wired directly to an instrument rack without an extension cable?

A: No. The transducer system requires a precise total electrical length match (typically 5.0 meters or 9.0 meters) to maintain loop tuning. A 1.0-meter probe must be combined with an appropriate 4.0-meter or 8.0-meter extension cable to connect to the Proximitor Sensor.

Q: Is this 3300 XL probe backwards compatible with older 7200 series monitoring hardware?

A: While physical mounting dimensions may allow installation, the internal electrical properties of the 3300 XL probe are optimized to generate a 7.87 V/mm (200 mV/mil) scale factor when combined with a matching 3300 XL Proximitor. Mixing mismatched components will degrade linear range performance.

Field Installation Guidelines

Torque Rating Interlocks: When fastening the 70 mm fully threaded metric housing into the machine port, do not exceed the structural limit of 33.9 N-m (300 in-lb) to prevent distortion of the inductive coil shell.
Cable Handling & Routing Restrictions: Protect the 75 Ohm standard coaxial cable lead from sharp field edges. Maintain a minimum mechanical bend radius of 25.4 mm (1.0 inch) across the entire run to prevent conductor degradation.
Shield Grounding Protocols: The outer shield of the ClickLoc miniature coaxial line must maintain complete isolation from the machine case ground. System grounding must be managed strictly at the instrument monitor enclosure terminal.

ماذا يقول عملاؤنا عنا؟

دعم طوارئ ممتاز!

تعطل خط إنتاجنا بسبب عطل في شاشة بنتلي نيفادا. وجدناها متوفرة لدينا في المخزون، وقاموا بشحنها إلينا عبر DHL على الفور. عاد خط الإنتاج للعمل في غضون 48 ساعة - لقد أنقذت هذه الشاشة مصنعنا حقًا.

مارك تومسون

مدير الصيانة، الولايات المتحدة الأمريكية

مصدر موثوق لقطع الغيار الجديدة

يُعدّ العثور على وحدات أصلية جديدة تمامًا أمرًا بالغ الأهمية لسلامتنا. يُقدّم هذا الفريق مكونات جديدة من المصنع مع شهادات اعتماد كاملة. والتزامهم ببيع المنتجات الجديدة فقط يجعلهم شريكنا الأكثر ثقة.

روبرت هوفمان

رئيس قسم الهندسة، ألمانيا

خدمة وجودة من الدرجة الأولى

نستورد قطع غيار هانيويل وشنايدر من هنا منذ عامين. تصل كل شحنة مغلفة بإحكام مع الحفاظ على أختام المصنع الأصلية. نتميز بالتواصل الواضح وأفضل أوقات التسليم في هذا المجال.