330709-000-060-10-02-00 Bently Nevada Proximity Probe

Bently Nevada 330709-000-060-10-02-00 3300 XL Series Proximity Sensors

Bently Nevada 330709-000-060-10-02-00 3300 XL Series Proximity Sensors

التوفر: 10 متوفر في المخزون

Configured for physical displacement measurement in machine monitoring systems, the Bently Nevada 330709-000-060-10-02-00 (330709 Proximity Probe) provides direct physical/electrical execution....

رمز المنتج: 330709-000-060-10-02-00

Manufacturer: Bently Nevada
Product No.: 330709-000-060-10-02-00
Product Type: Proximity Sensors
Product Origin: USA
Payment:T/T, Western Union
Weight: 3000g
Shipping port: Xiamen
Warranty: 12 months

وصف التقييمات

Configured for physical displacement measurement in machine monitoring systems, the Bently Nevada 330709-000-060-10-02-00 (330709 Proximity Probe) provides direct physical/electrical execution.

Suffix Breakdown & Model Matrix

The suffix structure of this 11 mm metric-threaded proximity probe model is configured as follows:

330709: 3300 XL 11 mm Proximity Probe base model with M16 x 1.5 metric thread (without armor).
000: Unthreaded Length Option of 0 mm.
060: Overall Case Length Option of 60 mm.
10: Total Length Option of 1.0 meter (3.3 feet).
02: Connector and Cable-Type Option utilizing a miniature coaxial ClickLoc connector on standard cable.
00: Agency Approval Option indicating no approvals are required.

Hardware Specifications

Parameter	Specification
Model	330709-000-060-10-02-00
Brand	Bently Nevada
Origin	USA
Weight	0.15 kg (Net weight), 3.0 kg (Shipping weight)
Dimensions	11.0 mm tip diameter, 60 mm case length, 1.0 m cable length
Thread Profile	M16 x 1.5 metric thread
Operating Temp	-51 to +177 deg C
Power Consumption	Passive sensor (0 W)
Connector Type	Miniature coaxial ClickLoc connector
Cable Type	Standard coaxial cable

Eddy-Current Probe Scaling & Rotor Dynamics

This 11 mm metric-threaded eddy-current probe generates a high-frequency electromagnetic field at its tip to monitor rotor dynamics without physical contact. To achieve standard scale factor calibration of 3.94 V/mm (100 mV/mil), the probe must operate with a matched 3300 XL 11 mm Proximitor sensor and corresponding extension cable. During mechanical installation, technicians must perform gap voltage validation, adjusting the physical position until the output of the system reads -10 VDC, representing the center of the linear operating range. This step minimizes calibration errors and optimizes cross-talk suppression when placing multiple sensors in close radial proximity on the shaft.

Frequently Asked Questions

Q: Can this 330709-000-060-10-02-00 probe be directly wired to an 8 mm 3300 XL Proximitor?

A: No. The 11 mm probe coil has different inductive and physical parameters than an 8 mm probe. Connecting this probe to an 8 mm Proximitor will cause severe impedance mismatching and invalid scaling.

Q: Is this proximity probe compatible with hot-swapping at the coaxial connector under active power?

A: Yes. The probe is a passive inductive device. Disconnecting or connecting the coaxial ClickLoc connector while the Proximitor sensor is powered does not cause electrical damage or system risk.

Field Installation Guidelines

Mechanical Thread Mounting: Manually thread the M16 x 1.5 body into the bracket to ensure correct alignment. Do not exceed the maximum torque limits specified for metric non-armored probe bodies to prevent structural damage to the probe coil.
Electrical Gap Adjustment: Connect a voltmeter to the Proximitor sensor terminal block. Rotate the probe body into the mounting port until the output voltage matches the target value of -10.0 VDC. Lock the probe body using the provided locknuts.
Coaxial Connector Isolation: Always install the ClickLoc connector protector over the coaxial connection. The outer copper shield of the coaxial cable must remain electrically isolated from the machine housing to prevent industrial ground loop noise from corrupting the dynamic vibration readings.

ماذا يقول عملاؤنا عنا؟

دعم طوارئ ممتاز!

تعطل خط إنتاجنا بسبب عطل في شاشة بنتلي نيفادا. وجدناها متوفرة لدينا في المخزون، وقاموا بشحنها إلينا عبر DHL على الفور. عاد خط الإنتاج للعمل في غضون 48 ساعة - لقد أنقذت هذه الشاشة مصنعنا حقًا.

مارك تومسون

مدير الصيانة، الولايات المتحدة الأمريكية

مصدر موثوق لقطع الغيار الجديدة

يُعدّ العثور على وحدات أصلية جديدة تمامًا أمرًا بالغ الأهمية لسلامتنا. يُقدّم هذا الفريق مكونات جديدة من المصنع مع شهادات اعتماد كاملة. والتزامهم ببيع المنتجات الجديدة فقط يجعلهم شريكنا الأكثر ثقة.

روبرت هوفمان

رئيس قسم الهندسة، ألمانيا

خدمة وجودة من الدرجة الأولى

نستورد قطع غيار هانيويل وشنايدر من هنا منذ عامين. تصل كل شحنة مغلفة بإحكام مع الحفاظ على أختام المصنع الأصلية. نتميز بالتواصل الواضح وأفضل أوقات التسليم في هذا المجال.