Configured for 24 VDC discrete signal switching in VersaMax I/O systems, the General Electric IC200MDL730 (IC200MDL730 Discrete Output Module) provides direct physical/electrical execution. The module drives up to 8 positive logic (sourcing) output channels, routing current from an external 18 to 30 VDC power supply to external loads at up to 2.0 A per point. Designed with integrated overcurrent and short-circuit protection circuits, the hardware continuously monitors field loops and signals point faults back to the controller while visually indicating fault states via individual channel amber LEDs.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | IC200MDL730 |
| Brand | General Electric |
| Origin | USA |
| Weight | 0.17 kg (0.38 lbs) |
| Dimensions | Standard VersaMax Carrier Profile |
| Operating Temp | 0 to 60 deg C |
| Power Consumption | 50 mA @ 5 VDC (Backplane draw) |
| Module ID | FFFF8140 |
| Number of Points | 8 Discrete Outputs |
| Output Type | Sourcing / Positive Logic |
| Output Voltage Range | 17.5 to 30 VDC (24 VDC nominal) |
| Maximum Load Current | 2.0 A per point @ 30 VDC |
| External Power Supply | 18 to 30 VDC (24 VDC nominal) |
| Isolation | None (group-to-group or point-to-point) |
| Circuit Protection | Overcurrent and short-circuit protection |
| Status Indicators | 8 Output Point LEDs, OK LED, FLD PWR LED |
Deterministic Network Attributes & Backplane Integration
The IC200MDL730 maintains high backplane bus communication velocity across VersaMax I/O stations, drawing 50 mA from the 5 VDC backplane supply to power internal logic. It interfaces directly with CPU network interface units across Profinet or EtherNet/IP deterministic networks to execute real-time discrete switching operations. Native firmware flash compatibility guarantees continuous diagnostic reporting—including point-level overload detection—while maintaining deterministic loop refresh speeds across scalable I/O carrier topologies.
Frequently Asked Questions
Q: What power sequencing procedure is required when applying field power to the module?
A: Backplane power must be established for at least 1 second before applying external field power (18 to 30 VDC) to ensure internal control logic initializes prior to energizing output circuits.
Q: How does the IC200MDL730 indicate short-circuit or overload conditions on field outputs?
A: The module illuminates an amber LED corresponding to the faulted channel point and reports a point-fault signal to the VersaMax CPU for system-level alarm logging.
Q: Is hot-swapping supported for the IC200MDL730?
A: Hot insertion is supported on VersaMax carrier bases; however, accurate physical alignment during insertion is required to avoid pin bending or backplane bus communication disruption.
Field Installation Guidelines
-
Power Isolation: Disconnect main power to the cabinet and field loops prior to mounting or removing the carrier module.
-
Backplane Power Initialization: Ensure the CPU or expansion receiver energizes the 5 VDC backplane bus for 1 second before switching on the external 18 to 30 VDC field power supply.
-
Field Device Wiring: Wire positive logic loads to the channel output terminals on the carrier base. Connect the common side of the load to the negative rail of the external 24 VDC supply.
-
Power Supply Capacity: Verify that the external DC field power supply provides sufficient transient current capacity during short-circuit events to prevent voltage dips on adjacent field loops.
-
Grounding & Shielding: Ensure the mounting DIN rail is properly bonded to protective earth (PE) to mitigate electromagnetic interference in high-current switching installations.
ماذا يقول عملاؤنا عنا؟
دعم طوارئ ممتاز!
تعطل خط إنتاجنا بسبب عطل في شاشة بنتلي نيفادا. وجدناها متوفرة لدينا في المخزون، وقاموا بشحنها إلينا عبر DHL على الفور. عاد خط الإنتاج للعمل في غضون 48 ساعة - لقد أنقذت هذه الشاشة مصنعنا حقًا.
مارك تومسون
مدير الصيانة، الولايات المتحدة الأمريكيةمصدر موثوق لقطع الغيار الجديدة
يُعدّ العثور على وحدات أصلية جديدة تمامًا أمرًا بالغ الأهمية لسلامتنا. يُقدّم هذا الفريق مكونات جديدة من المصنع مع شهادات اعتماد كاملة. والتزامهم ببيع المنتجات الجديدة فقط يجعلهم شريكنا الأكثر ثقة.
روبرت هوفمان
رئيس قسم الهندسة، ألمانياخدمة وجودة من الدرجة الأولى
نستورد قطع غيار هانيويل وشنايدر من هنا منذ عامين. تصل كل شحنة مغلفة بإحكام مع الحفاظ على أختام المصنع الأصلية. نتميز بالتواصل الواضح وأفضل أوقات التسليم في هذا المجال.
لوكاس مولر
مدير العمليات، ألمانياالمنتجات ذات الصلة
مرشد
Translation missing: ar.general.search.loading