IC693PBS201 GE Series 90-30 Datasheet & Technical Manual

IC693PBS201 GE Series 90-30 Profibus DP Slave Module

IC693PBS201 GE Series 90-30 Profibus DP Slave Module

Disponibilidad: 10 Quedan en stock

The GE IC693PBS201, also cataloged as the IC693PBS201 Profibus Slave Module, operates as a dedicated hardware component for field network...

Código: IC693PBS201

Manufacturer: GE Fanuc
Product No.: IC693PBS201
Product Type: Profibus Slave Modules
Product Origin: USA
Payment:T/T, Western Union
Weight: 260g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

The GE IC693PBS201, also cataloged as the IC693PBS201 Profibus Slave Module, operates as a dedicated hardware component for field network communication interfacing within Series 90-30 platforms. Occupying a single chassis slot, the module acts as a remote communication adapter transferring up to 244 Bytes of input data and 244 Bytes of output data cyclically between local baseplate I/O modules and a centralized Profibus DP master controller.

Hardware Specifications

Parameter	Specification
Model	IC693PBS201
Brand	GE Fanuc Emerson
Series	Series 90-30
Product Type	Profibus Slave Modules
Communication Protocol	Profibus DP (Slave)
Data Capacity	244 Bytes input / 244 Bytes output
Communication Speeds	9.6k, 19.2k, 93.75k, 187.5k, 500k, 1.5M, 3M, 6M, 12M Baud
Physical Interfaces	2x 9-pin female D-shell connectors (Port 1: Service, Port 2: Slave)
Power Consumption	450 mA at 5 VDC (backplane draw)
Baseplate Compatibility	Any slot except Slot 1 of CPU baseplate
Operating Temp	0 to 60 deg C
Dimensions	Single-slot Series 90-30 module footprint
Weight	0.26 kg (0.56 lbs)
Origin	USA

Backplane Bus Interfacing and Communication Latency

The IC693PBS201 coordinates data transfer across the Series 90-30 parallel backplane to maintain high backplane bus communication velocity during slave cycle execution. Configured using Proficy Machine Edition Logic Developer, the module validates communication status via an internal Slave Status Word. Onboard serial processing handles baud rates up to 12 Mbps while maintaining full firmware flash compatibility for local service updates without disrupting adjacent module hardware operations.

Frequently Asked Questions

Q: What baseplate slot locations are supported for the IC693PBS201?

A: The module can be installed in any available I/O slot across Series 90-30 baseplates, excluding Slot 1 of the CPU baseplate, which is dedicated exclusively to the power supply module.

Q: What are the primary functions of the two 9-pin D-shell communication ports?

A: Port 1 serves as an RS-232 service interface for firmware modifications and local maintenance, while Port 2 provides the primary connection to the external Profibus DP network.

Q: What is the maximum backplane power current draw for this module?

A: The IC693PBS201 draws a nominal 450 mA from the internal 5 VDC backplane logic power rail.

Field Installation Guidelines

Disconnect system rack power and external I/O field power sources prior to inserting or removing the module from the baseplate.
Wear an ESD wrist strap connected to a bare metal enclosure ground point before handling the circuit assembly.
Align the single-slot module card edges with the baseplate slot guides and seat the unit firmly until the rear connector latches engage.
Connect the Profibus network trunk to the 9-pin D-shell slave port using approved shielded cable (e.g., Belden 3079A or Siemens 6XV1), ensuring proper line termination resistors are enabled at both physical ends of the segment.
Supply power to the rack and verify communication status using the diagnostic LED indicators and Proficy Machine Edition configuration software.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.