F3LE01-5T Yokogawa STARDOM Datasheet & Technical Manual

F3LE01-5T Yokogawa STARDOM FCN FCJ Ethernet Interface Module

F3LE01-5T Yokogawa STARDOM FCN FCJ Ethernet Interface Module

Availability: 10 left in stock

Yokogawa F3LE01-5T Ethernet Interface Module Configured for high-speed data transmission in STARDOM FCN/FCJ autonomous controller networks, the Yokogawa F3LE01-5T (F3LE01...

SKU: F3LE01-5T

Manufacturer: Yokogawa
Product No.: F3LE01-5T
Product Type: Ethernet Interface Modules
Product Origin: JAPAN
Payment:T/T, Western Union
Weight: 110g
Shipping port: Xiamen
Warranty: 12 months

Description Reviews

Yokogawa F3LE01-5T Ethernet Interface Module

Configured for high-speed data transmission in STARDOM FCN/FCJ autonomous controller networks, the Yokogawa F3LE01-5T (F3LE01 Ethernet Interface Module) provides direct physical/electrical execution. The hardware establishes deterministic network link paths over standard 10Base-T copper topology, routing processed data frames from the internal logic rack directly to the industrial supervisory control architecture.

Layout Configuration Selection: Layout 1

Hardware Specifications

Parameter	Specification
Model	F3LE01-5T
Brand	Yokogawa Electric Corporation
Origin	Japan
Weight	0.11 kg (0.25 lbs)
Dimensions	130 x 130 x 32 mm
Operating Temp	-20 to +60 deg C
Power Consumption	24 VDC external supply / Backplane derived logic power
Interface Speed	10Base-T physical layer communication
Network Protocol Support	Ethernet, integration with Vnet/IP subnet matrix
Controller Compatibility	STARDOM FCN and FCJ autonomous controller systems
Memory Subsystem	8 MB program execution space with battery-backed SRAM tracking
System Redundancy	Dual-redundant hardware layout configuration supported
Hardware Suffix Type	S1 configuration specification
Storage Temperature	-40 to +70 deg C
Humidity Envelope	5 to 95% RH (non-condensing)

Process Control & DCS Instrumentation Technical Attributes

This communications module integrates an isolated physical layer circuit matching the 10Base-T network standard to process logic variables across the internal I/O sub-bus matrix. The dual-redundant architecture enables parallel station tracking over separate network switches, managing failover routines under 100 ms without interrupting active process loops or drops in data registers. To block common-mode electrical transients present in industrial environments, the interface implements high-voltage galvanic channel-to-system isolation, preventing field-induced loop noise from corrupting the internal autonomous CPU execution cycles.

Frequently Asked Questions

Q: How does the network interface handle a loss of link state on the primary cable path?

A: The module communicates status parameters continuously across the baseplate backplane; upon detecting a physical line break or packet timeout, the tracking logic switches execution commands to the secondary redundant module slot within one scanning cycle.

Q: What is the significance of the "5T" suffix designation on this specific hardware model?

A: The "5T" suffix defines the 10Base-T copper connectivity variant intended for standard cabinet wiring installations, indicating the module lacks integrated intrinsic safety barriers or specialized explosion-proof certifications.

Field Installation Guidelines

Baseplate Component Locking: Insert the module vertically into the designated slot of the STARDOM rack base assembly, pushing evenly until the multi-pin connector locks completely into the system bus.
Network Interface Cabling: Terminate high-quality shielded twisted-pair (STP) Category 5e or Category 6 cables into the RJ-45 ports, ensuring the outer metallic connector boot grounds against the module frame.
Shield Ground Tracking: Ground all networking conduit runs and structural metal panels to the primary plant instrument clean earth bus bar, keeping loop impedances low to reduce stray electromagnetic fields.
Thermal Boundary Clearance: Verify that the 130 x 130 x 32 mm installation space has sufficient clearances at the top and bottom of the rack to allow natural convective airflow to maintain temperatures within the -20 to +60 deg C limits.

What's clients say about us

Excellent Emergency Support!

Our production line was down due to a faulty Bently Nevada monitor. We found it in stock here and they shipped it via DHL immediately. Back in operation within 48 hours—truly a lifesaver for our plant.

Mark Thompson

Maintenance Manager, USA

Reliable Source for New Spares

Finding brand new, original modules is critical for our safety. This team delivers factory-fresh components with full certification. Their commitment to only selling new products makes them our most trusted partner.

Robert Hoffmann

Engineering Lead, Germany

Top-tier Service and Quality

We have sourced Honeywell and Schneider parts here for two years. Every shipment arrives well-packaged with original factory seals intact. Clear communication and the best lead times in the industry.