FBM223 P0917HD Foxboro PROFIBUS Module

Foxboro FBM223 P0917HD I/A Series Communication Interface Module

Foxboro FBM223 P0917HD I/A Series Communication Interface Module

Availability: 10 left in stock

Foxboro FBM223 P0917HD I/A Series Communication Interface Module Configured for high-speed industrial network integration in Foxboro I/A Series DCS platforms,...

SKU: P0917HD

Manufacturer: Foxboro
Product No.: P0917HD
Product Type: Communication Interface Modules
Product Origin: USA
Payment:T/T, Western Union
Weight: 200g
Shipping port: Xiamen
Warranty: 12 months

Description Reviews

Foxboro FBM223 P0917HD I/A Series Communication Interface Module

Configured for high-speed industrial network integration in Foxboro I/A Series DCS platforms, the Foxboro FBM223 P0917HD (FBM223 PROFIBUS-DP Communication Interface Module) provides direct physical/electrical execution. This module executes real-time fieldbus data transfer between host system processors and distributed field devices across dual isolated communication channels without adding process latencies.

Hardware Specifications

Parameter	Specification
Model	FBM223 P0917HD
Brand	Foxboro (Schneider Electric)
Origin	USA
Weight	0.2 kg
Dimensions	4.4 cm x 10.2 cm x 10.8 cm
Operating Temp	-40 deg C to +70 deg C
Power Consumption	6 W max
Heat Dissipation	6 W max
Input Voltage Range	24 VDC (+5% / -10%)
Protocol Support	PROFIBUS-DP Master (EN 50170)
Field Bus Channels	2 isolated PROFIBUS-DP buses
Baud Rate	9.6 kbit/s to 12 Mbit/s
Device Capacity	Up to 126 slave devices
Isolation Voltage	Galvanic isolation, 1500 VDC
Mounting	Standard FGDC/FGDM baseplate
Ingress Protection	IP20

Channel-to-Channel Isolation & Fieldbus Gateway Performance

The FBM223 module relies on channel-to-channel isolation protocols alongside galvanic isolation rated up to 1500 VDC to safeguard internal system logic against ground loops and field-side electrical surges. Integrating directly into the backplane bus, the hardware handles high-density PROFIBUS-DP master transactions across a wide transmission spectrum from 9.6 kbit/s up to 12 Mbit/s. This electrical isolation prevents noise propagation between the redundant PROFIBUS segments, ensuring deterministic timing cycles and reliable device communication within hazardous, high-interference industrial field zones.

Frequently Asked Questions

Q: What are the backplane isolation limits and hot-swap restrictions for the FBM223?

A: The module incorporates 1500 VDC galvanic isolation between the field-side PROFIBUS-DP network and the internal backplane logic. Operators can safely perform live hot-swapping directly on the active FGDC/FGDM baseplate without disrupting adjacent operational modules or forcing a DCS system shutdown.

Q: How does the module handle dual-channel fieldbus redundancy?

A: The hardware houses two independent, isolated PROFIBUS-DP master channels. If an external wiring fault or signal interruption occurs on one physical bus, the module maintains continuous deterministic data exchange over the parallel channel, preserving real-time field updates.

Q: Does installing the FBM223 require external power wiring to the front panel?

A: No. Primary 24 VDC operational power is supplied directly through the internal connectors on the underlying backplane baseplate structure, keeping external field terminal connections clean and localized to communication lines.

Field Installation Guidelines

Ensure proper field installation and stable long-term operation by strictly following these hardware integration requirements:

Seat the module firmly into its designated FGDC or FGDM baseplate slot until the mechanical locking latches fully engage.
Maintain standard RS-485/PROFIBUS-DP cable shielding practices by grounding signal shields at the specified baseplate terminal blocks to prevent stray noise coupling.
Install standard 220 ohm bus termination resistors at both physical ends of each PROFIBUS-DP network segment to suppress signal reflections at high baud rates.
Route field communication cables away from high-voltage AC motor drives, switched power conductors, and heavy industrial inductive loads.
Verify that the ambient operating environment remains within the rated enclosure limits of -40 deg C to +70 deg C and that airflow around the baseplate remains unobstructed.

What's clients say about us

Excellent Emergency Support!

Our production line was down due to a faulty Bently Nevada monitor. We found it in stock here and they shipped it via DHL immediately. Back in operation within 48 hours—truly a lifesaver for our plant.

Mark Thompson

Maintenance Manager, USA

Reliable Source for New Spares

Finding brand new, original modules is critical for our safety. This team delivers factory-fresh components with full certification. Their commitment to only selling new products makes them our most trusted partner.

Robert Hoffmann

Engineering Lead, Germany

Top-tier Service and Quality

We have sourced Honeywell and Schneider parts here for two years. Every shipment arrives well-packaged with original factory seals intact. Clear communication and the best lead times in the industry.