MS08*B Yokogawa CENTUM VP Series Datasheet & Technical Manual

Yokogawa MS32*A S9750BH-05 Power Supply Module Card

Yokogawa MS32*A S9750BH-05 Power Supply Module Card

التوفر: 10 متوفر في المخزون

Yokogawa MS32*A System Power Supply Module The Yokogawa MS32*A, also cataloged as the MS32 System Power Supply Module, operates as...

رمز المنتج: MS31*A

Manufacturer: Yokogawa
Product No.: MS31*A
Product Type: Power Supply Modules
Product Origin: JAPAN
Payment:T/T, Western Union
Weight: 450g
Shipping port: Xiamen
Warranty: 12 months

وصف التقييمات

Yokogawa MS32*A System Power Supply Module

The Yokogawa MS32*A, also cataloged as the MS32 System Power Supply Module, operates as a dedicated hardware component for converting incoming DC power into regulated outputs within CENTUM VP and CS 3000 networks. The card installs directly into a Field Control Unit (FCU) rack slot to drive heavy-duty backplane logic circuits and source operating current to large arrays of distributed computing and communication cards.

Hardware Specifications

Parameter	Specification
Model	MS32*A (Part Number: S9750BH-05)
Brand	Yokogawa
Origin	Japan
Weight	0.45 kg
Dimensions	120 mm x 25 mm x 130 mm
Operating Temp	0 to 60 deg C
Power Consumption	150 W
System Compatibility	CENTUM VP, CS 3000
Input Voltage	24 VDC (nominal)
Input Range	20 to 30 VDC
Output Voltage	5 VDC
Output Current	Up to 32 A
Isolation	1500 VAC (input-to-output, 1 min)
Protection Features	Overcurrent, overvoltage, short-circuit protection
Humidity Range	5 to 95% RH (non-condensing)

Power Conditioning & Channel Isolation

The power supply architecture accepts a nominal 24 VDC input and utilizes high-capacity switching topologies to generate a regulated 5 VDC output rail capable of sourcing up to 32 A. To block common-mode electrical noise and prevent ground-loop currents from degrading downstream computing logic, the hardware incorporates internal galvanic channel-to-channel isolation circuits rated at 1500 VAC. The module integrates overcurrent, overvoltage, and short-circuit protection loops that clamp active field faults automatically, preventing upstream terminal failures from destroying internal subrack components. Real-time diagnosis of internal electrical states routes directly to front-mounted physical LED indicators that display independent statuses for RUN, FAIL, and input power paths.

Frequently Asked Questions

Q: How does the 32 A current capacity alter the configuration requirements for dual-redundant power setups?

A: When two modules form a dual-redundant pair within the backplane, an integrated diode-ORing configuration balances the high-current distribution. Both units share the subrack load during normal operation, but if one hardware block drops offline, the remaining module instantly picks up the full 32 A demand without inducing a voltage sag on the 5 VDC bus line.

Q: What specific hardware check must you perform if the front-panel FAIL LED illuminates under normal 24 VDC input voltage?

A: An active FAIL LED indicates that internal secondary monitoring has detected either an overvoltage trip or an under-voltage sag on the internal 5 VDC output rail, or that the internal heat-sink thermal thresholds have been exceeded. This hardware state signifies that the card requires immediate replacement to prevent a loss of chassis redundancy.

Field Installation Guidelines

Subrack Alignment and Seating: Align the card along the dedicated guide tracks within the FCU subrack. Push the assembly firmly perpendicular to the backplane until the high-density system connectors lock completely, and tighten all mechanical retention fasteners to prevent pin fretting caused by high-frequency industrial environments.
Input Power Conductor Routing: Terminate the incoming 24 VDC supply lines using heavy-gauge industrial conductors sized to handle the 150 W power profile. Maintain strict physical separation between these DC lines and any high-voltage AC power or motor drive cables inside the enclosure cabinet to mitigate electromagnetic cross-talk.
Thermal Displacement Clearance: Ensure that all vertical cabinet cooling pathways remain clear. Because the module generates considerable thermal dissipation under full 32 A current loading, it requires unhindered convective airflow to hold the operating temperature within the specified 0 to 60 deg C threshold.

ماذا يقول عملاؤنا عنا؟

دعم طوارئ ممتاز!

تعطل خط إنتاجنا بسبب عطل في شاشة بنتلي نيفادا. وجدناها متوفرة لدينا في المخزون، وقاموا بشحنها إلينا عبر DHL على الفور. عاد خط الإنتاج للعمل في غضون 48 ساعة - لقد أنقذت هذه الشاشة مصنعنا حقًا.

مارك تومسون

مدير الصيانة، الولايات المتحدة الأمريكية

مصدر موثوق لقطع الغيار الجديدة

يُعدّ العثور على وحدات أصلية جديدة تمامًا أمرًا بالغ الأهمية لسلامتنا. يُقدّم هذا الفريق مكونات جديدة من المصنع مع شهادات اعتماد كاملة. والتزامهم ببيع المنتجات الجديدة فقط يجعلهم شريكنا الأكثر ثقة.

روبرت هوفمان

رئيس قسم الهندسة، ألمانيا

خدمة وجودة من الدرجة الأولى

نستورد قطع غيار هانيويل وشنايدر من هنا منذ عامين. تصل كل شحنة مغلفة بإحكام مع الحفاظ على أختام المصنع الأصلية. نتميز بالتواصل الواضح وأفضل أوقات التسليم في هذا المجال.