IC697BEM713 GE Series 90-70 Bus Module

GE IC697BEM713 Series 90-70 Bus Expansion Module

GE IC697BEM713 Series 90-70 Bus Expansion Module

Disponibilidad: 10 Quedan en stock

The GE IC697BEM713, also cataloged as the IC697BEM713 Bus Transmitter Module, operates as a dedicated hardware component for local backplane...

Código: IC697BEM713

Manufacturer: GE Fanuc
Product No.: IC697BEM713
Product Type: Bus Expansion Modules
Product Origin: USA
Payment:T/T, Western Union
Weight: 450g
Shipping port: Xiamen
Warranty: 12 months

Descripción Reseñas

The GE IC697BEM713, also cataloged as the IC697BEM713 Bus Transmitter Module, operates as a dedicated hardware component for local backplane bus extension within Series 90-70 platforms. The single-slot interface module transmits high-speed logic and I/O data parallel lines from the primary processor chassis to peripheral racks, ensuring physical synchronization across multi-rack physical assemblies.

Hardware Specifications

Parameter	Specification
Model	IC697BEM713
Brand	GE Fanuc Emerson
Origin	USA
Weight	0.43 kg (0.94 lbs)
Dimensions	Single-slot rack width
Operating Temp	0 to 60 deg C
Power Consumption	1.4 A @ 5 VDC input
Module Position	Any chassis slot except Slot 1
Max Receiver Capacity	7x IC697BEM711 Bus Receiver Modules
Max Interconnect Distance	50 ft (15 m) absolute loop limit
Effective Data Rate	500 Kbytes / sec (Programmer & Expansion paths)
Physical Interfaces	1x Parallel Programmer Port, 1x Expansion Port
Status Indications	OK (Top), PGMR (Middle), Last Rack Bus (Bottom)
Signal Isolation	Non-isolated differential communication
Bus Standard	VME C.1 compliant architecture

Industrial Control and Network Determinism

The IC697BEM713 enforces specific backplane bus communication velocity configurations to expand the control framework without degrading central transaction speed. By establishing dedicated multi-rack routing, the module maintains structured I/O density scaling profiles up to seven auxiliary racks while keeping logic propagation delays beneath sub-millisecond scanning thresholds. Firmware flash compatibility rules require full hardware initialization and downstream polling before the main status register allows the CPU to enter operational RUN status.

Frequently Asked Questions

Q: Does this expansion interface support unpowered hot-swapping or physical extraction during operation?

A: No. The IC697BEM713 does not support insertion or removal while the chassis is powered. The main rack power supply must be completely isolated prior to mounting or removing the module to prevent electrical transients from disrupting the VME parallel bus.

Q: What is the cause of the bottom status LED failing to illuminate during initial system boot?

A: The bottom LED tracks expansion bus health. If it remains off, it indicates a link continuity fault, an unpowered downstream rack, or a missing IC697ACC702 terminating resistor at the final physical expansion output port.

Field Installation Guidelines

Bus Termination Requirements: Install an IC697ACC702 terminating resistor directly onto the Expansion Port Out connector of the seventh or final physical Bus Receiver Module in the daisy chain to stabilize the differential signals.
Cable Selection and Routing Restrictions: Use approved low-skew expansion cables (IC600WD005A, IC600WD010A, IC600WD025A, or IC600WD050A). Route these parallel lines completely clear of high-voltage motor starters and AC distribution panels.
Chassis Alignment Constraints: Place the module in any available base rack slot except for Slot 1, which must be strictly reserved for the primary Series 90-70 Central Processing Unit.

¿Qué dicen nuestros clientes sobre nosotros?

¡Excelente soporte de emergencia!

Nuestra línea de producción se paró debido a un monitor Bently Nevada defectuoso. Lo encontramos en stock aquí y lo enviaron por DHL de inmediato. Volvió a funcionar en 48 horas, lo que realmente salvó nuestra planta.

Mark Thompson

Gerente de Mantenimiento, EE. UU.

Fuente confiable de repuestos nuevos

Encontrar módulos nuevos y originales es fundamental para nuestra seguridad. Este equipo entrega componentes de fábrica con certificación completa. Su compromiso de vender únicamente productos nuevos los convierte en nuestro socio de mayor confianza.

Robert Hoffmann

Jefe de ingeniería, Alemania

Servicio y calidad de primer nivel

Llevamos dos años abasteciendo aquí piezas de Honeywell y Schneider. Todos nuestros envíos llegan perfectamente embalados, con los precintos originales de fábrica intactos. Ofrecemos una comunicación clara y los mejores plazos de entrega del sector.