P0914SQ Foxboro Analog Input Module

P0914SQ FBM201 Foxboro I/A Series Analog Input Modules

P0914SQ FBM201 Foxboro I/A Series Analog Input Modules

Availability: 10 left in stock

Foxboro P0914SQ FBM201 Analog Input Modules Configured for 8-channel analog input signal acquisition in Foxboro I/A Series platforms, the Foxboro...

SKU: FBM201 P0914SQ

Manufacturer: Foxboro
Product No.: FBM201 P0914SQ
Product Type: Analog Input Modules
Product Origin: USA
Payment:T/T, Western Union
Weight: 300g
Shipping port: Xiamen
Warranty: 12 months

Description Reviews

Foxboro P0914SQ FBM201 Analog Input Modules

Configured for 8-channel analog input signal acquisition in Foxboro I/A Series platforms, the Foxboro P0914SQ (FBM201 Analog Input Module) provides direct physical/electrical execution. The module processes standard 0 to 20.4 mA DC current signals from field transmitters and transfers digital values across the redundant Fieldbus interface.

Suffix Breakdown & Model Matrix

The FBM201 platform uses designated part numbers to identify hardware modules and baseplate component configurations:

FBM201 / P0914SQ: Primary functional module assembly representing the 8-channel channel-isolated analog input module.
P0914SQ: Physical hardware part number designation for the FBM201 module block.

Hardware Specifications

Parameter	Specification
Model	P0914SQ (FBM201)
Brand	Foxboro
Origin	USA
Weight	0.3 kg
Dimensions	4.5 cm x 11 cm x 11.5 cm
Operating Temp	0 to +60 deg C
Power Consumption	Standard backplane 24 VDC supply load
Module Type	Analog Input
Input Channels	8 Isolated Analog Input Channels
Input Range	0 to 20.4 mA DC (Standard 4-20 mA)
Measurement Accuracy	+/-0.05% of span
A/D Resolution	12 to 16-bit configurable
Isolation	Galvanic isolation withstands 600 VAC
Communication	Redundant Fieldbus Interface
Onboard Memory	16 MB SDRAM, 32 MB Flash
Power Input	24 VDC (Redundancy Supported)

Process Control & Channel Isolation Profiles

The module integrates individual channel galvanic isolation barriers rated to withstand up to 600 VAC, preventing field ground loops and high-voltage electrical surges from damaging internal backplane logic. Additionally, the high-resolution A/D conversion circuit processes raw current loops from 4-20 mA HART loop protocol transmitters, transmitting real-time process data frames over the redundant Fieldbus interface to maintain continuous controller execution without loop latency.

Frequently Asked Questions

Q: Does the P0914SQ module support hot-swapping under live baseplate power?

A: Yes, technicians can insert or remove the FBM201 module on an energized baseplate slot. Upon insertion, the system downloads system software parameters directly to the replacement unit without process disruption.

Q: Can the input channels process both 0-20 mA and 4-20 mA current loops?

A: Yes, the module accepts full input signals ranging from 0 to 20.4 mA DC, accommodating 0-20 mA ranges as well as standard 4-20 mA loops with built-in over-range diagnostic capability.

Field Installation Guidelines

First, align the module edge connector with the baseplate backplane slot, pressing firmly into position until the mechanical latch fully locks the unit to the chassis rail.

Next, run all 4-20 mA current loop wiring using shielded twisted-pair cables. Earth all cable drain shields at a single ground point on the main system ground bar to eliminate circulating earth currents. Route low-voltage signal cables in independent conduits, maintaining a minimum separation distance of 200 mm from high-voltage AC power lines to avoid inductive noise coupling.

Finally, verify that all screw connections on the associated Termination Assembly are torqued properly, and confirm that cabinet airflow clearance stays above 50 mm around chassis vents to enable adequate thermal dissipation.

What's clients say about us

Excellent Emergency Support!

Our production line was down due to a faulty Bently Nevada monitor. We found it in stock here and they shipped it via DHL immediately. Back in operation within 48 hours—truly a lifesaver for our plant.

Mark Thompson

Maintenance Manager, USA

Reliable Source for New Spares

Finding brand new, original modules is critical for our safety. This team delivers factory-fresh components with full certification. Their commitment to only selling new products makes them our most trusted partner.

Robert Hoffmann

Engineering Lead, Germany

Top-tier Service and Quality

We have sourced Honeywell and Schneider parts here for two years. Every shipment arrives well-packaged with original factory seals intact. Clear communication and the best lead times in the industry.