YOKOGAWA RC1*A Remote Control I/O Module
Configured for field signal termination and remote control execution in CENTUM VP and CS 3000 DCS platforms, the YOKOGAWA RC1*A (RC1A Remote I/O Module) provides direct physical/electrical execution of sensor-to-controller signal interface management.
Suffix Breakdown & Model Matrix
- RC1: Base model identifier for remote control I/O functionality and signal interface management.
- *A: Hardware revision and interface designation indicating compatibility with standard CENTUM DCS bus architectures.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | RC1*A |
| Brand | YOKOGAWA |
| Origin | Japan |
| Weight | 1.5 kg |
| Dimensions | 254 × 152 × 127 mm |
| Operating Temp | -20 deg C to +70 deg C |
| Power Consumption | 24 V DC |
| I/O Type | Remote I/O (Analog/Digital) |
| Isolation | Electrical |
| Protection | Built-in Surge Suppression |
DCS Process Control & Connectivity Attributes
The RC1*A executes high-speed signal processing between field instrumentation and the DCS backplane. To ensure data consistency across distributed networks, the module supports Modbus RTU and Modbus TCP communication protocols, allowing for deterministic data exchange. Channel-to-channel isolation is integrated within the signal path to prevent ground-loop interference and common-mode transients. Furthermore, the module facilitates cold junction compensation (CJC) for integrated temperature inputs, ensuring that terminal temperature fluctuations do not impact the precision of the connected instrumentation. Continuous self-diagnostics monitor the integrity of the input channels, providing proactive fault detection before signal degradation occurs.
Frequently Asked Questions
Q: Does the RC1*A support hot-swapping within the DCS rack? A: Module replacement must be performed in accordance with the specific system power-down sequence. Always verify the status of the redundant controller and communication bus before disconnecting the module to prevent backplane bus errors.
Q: Are the Modbus RTU and TCP protocols mutually exclusive on this module? A: The module architecture supports concurrent protocol handling; however, confirm the specific channel configuration mapping to ensure that digital data frames are correctly routed to the intended communication registers.
Q: How is the output current limit managed during actuator control? A: The module is rated for a continuous output current of 1 A. Over-current protection circuitry is active; ensure the connected load impedance does not exceed the power supply limits to prevent thermal shutdown of the output channel.
Field Installation Guidelines
- Mounting: Secure the module into the designated DCS rack slot. Tighten all retaining screws to ensure a low-impedance ground bond between the module chassis and the cabinet earth to maximize the effectiveness of the internal surge protection.
- Wiring: Utilize shielded twisted-pair instrumentation cable for all analog signal loops. Terminate cable shields at a centralized cabinet-level grounding rail to provide a low-resistance path for electromagnetic noise suppression.
- Isolation: Maintain a minimum clearance of 150 mm between signal cabling and high-voltage AC lines to prevent inductive noise coupling into the sensitive signal processing stages.
- Environmental: Ensure adequate airflow within the rack to maintain the module operating temperature within the specified range of -20 deg C to +70 deg C.
What's clients say about us
Excellent Emergency Support!
Our production line was down due to a faulty Bently Nevada monitor. We found it in stock here and they shipped it via DHL immediately. Back in operation within 48 hours—truly a lifesaver for our plant.
Mark Thompson
Maintenance Manager, USAReliable Source for New Spares
Finding brand new, original modules is critical for our safety. This team delivers factory-fresh components with full certification. Their commitment to only selling new products makes them our most trusted partner.
Robert Hoffmann
Engineering Lead, GermanyTop-tier Service and Quality
We have sourced Honeywell and Schneider parts here for two years. Every shipment arrives well-packaged with original factory seals intact. Clear communication and the best lead times in the industry.
Lucas Müller
Operations Director, GermanyRelated Products
PS31*A YOKOGAWA CENTUM VP Regulated Power Supply Module
$99.00
$199.00
YOKOGAWA RS81*B CENTUM XL Micro XL Interface Card
$99.00
$199.00
Multi Status Input Interface Card YOKOGAWA ST2*D CENTUM VP
$99.00
$199.00
ST3*D YOKOGAWA CENTUM VP Multi Status Input Interface Card
$99.00
$199.00
HART-Enabled Analog I/O Module YOKOGAWA VM1*B CENTUM VP
$99.00
$199.00
VM1*D YOKOGAWA CENTUM VP HART-Enabled Analog I/O Module
$99.00
$199.00
YOKOGAWA VM2*D CENTUM VP HART-Enabled Analog I/O Module
$99.00
$199.00
YNT512D-Q12 YOKOGAWA CENTUM VP Bus Repeater Module
$99.00
$199.00
YOKOGAWA AAM21-S2 CENTUM CS 3000 Analog Input Module
$99.00
$199.00
AMM12T-S2 YOKOGAWA CENTUM VP Analog Input Multiplexer Module
$99.00
$199.00
YOKOGAWA F3CX04-0N FA-M3 4-Channel Pulse Input Module
$99.00
$199.00
YOKOGAWA F3AD08-4V FA-M3 8-Channel Analog Input Module
$99.00
$199.00
F3BU13-0N FA-M3 YOKOGAWA 13-Slot PLC Base Unit
$99.00
$199.00
YOKOGAWA F3LE12-0T FA-M3 Ethernet Communication Module
$99.00
$199.00
YOKOGAWA ST4*D CENTUM VP Multi Status Input Interface Card
$99.00
$199.00
YOKOGAWA F3LR02-0N FA-M3 Redundancy Interface Module
$99.00
$199.00
Power Supply Module YOKOGAWA F3PU30-0S FA-M3 Series
$99.00
$199.00
F3XC08-0C FA-M3 YOKOGAWA Digital Output Relay Module
$99.00
$199.00
YOKOGAWA F3XD16-3F FA-M3 Series Digital Input Module
$99.00
$199.00
Analog Input Output Module YOKOGAWA AAP135-S00 CENTUM VP
$99.00
$199.00
AAM11-S2 YOKOGAWA Analog Input Module Process Control
$99.00
$199.00
YOKOGAWA AAI543-S50 CENTUM VP Analog Output Module
$99.00
$199.00
F3YC08-0C YOKOGAWA FA-M3 Datasheet & Technical Manual
$99.00
$199.00
Analog Input Module YOKOGAWA AAR145-S00 CENTUM VP
$99.00
$199.00
YOKOGAWA AAR181-S00 CENTUM VP Analog Input Module
$99.00
$199.00
Analog Input Modules CENTUM VP Series YOKOGAWA ADM11-S3
$99.00
$199.00
YOKOGAWA ADV159-P00 S1 Digital Input Module
$99.00
$199.00
Yokogawa AIP571 S1 Fieldbus Interface Module
$99.00
$199.00
AIP171 S2 Yokogawa Transceiver Control Module
$99.00
$199.00
Yokogawa ADV551-P00 Digital Output Module 32-Channel
$99.00
$199.00
Yokogawa AIP571 S2 Fieldbus Interface Module
$99.00
$199.00
Ethernet Communication Module DCS Yokogawa ALE111-S01
$99.00
$199.00
Yokogawa AMM32-S3 Digital Input Module 32-Channel
$99.00
$199.00
ALU4-D Yokogawa Modular Analog Input I/O System
$99.00
$199.00
Analog Input Module for DCS Control Yokogawa AMM42-S4
$99.00
$199.00
Yokogawa AMN11-S1 Analog I/O Nest for CENTUM Systems
$99.00
$199.00
Signal Conditioner and Communication Hub Yokogawa CM1*A
$99.00
$199.00
CNB-IIA Yokogawa Communication Network Bridge Module for DCS
$99.00
$199.00
Yokogawa CP99A-A CPU Module for Field Control Stations
$99.00
$199.00
Thermocouple Input Module Yokogawa CT5-TJ*A
$99.00
$199.00
Yokogawa CTL4-B PLC Interface Module for Industrial Control
$99.00
$199.00
Yokogawa DP97-B Distributed Control System Processor Card
$99.00
$199.00
AMM12 S3 YOKOGAWA Voltage Input Multiplexer Module
$99.00
$199.00
Guide
Translation missing: en.general.search.loading