140CPU67160S Schneider Electric Modicon Quantum Datasheet & Manual

Schneider Electric BMXART0814 Modicon X80 Analog Input Card

Schneider Electric BMXART0814 Modicon X80 Analog Input Card

Availability: 94 left in stock

Schneider Electric BMXART0814 Modicon X80 Analog Input Module The Schneider Electric BMXART0814, also cataloged as the BMXART0814 Analog Input Module,...

SKU: BMXART0814

Manufacturer: Schneider
Product No.: BMXART0814
Product Type: Analog Input Modules
Product Origin: France
Payment:T/T, Western Union
Weight: 165g
Shipping port: Xiamen
Warranty: 12 months

Description Reviews

Schneider Electric BMXART0814 Modicon X80 Analog Input Module

The Schneider Electric BMXART0814, also cataloged as the BMXART0814 Analog Input Module, operates as a dedicated hardware component for multi-channel analog voltage and current signal acquisition within Modicon M340 and M580 PLC platform networks. The hardware scans field-side instrumentation loops and executes successive approximation conversion sequences to update internal data registers via the chassis interface.

Hardware Specifications

Parameter	Specification
Model	BMXART0814
Brand	Schneider Electric
Origin	France
Weight	0.165 kg (0.364 lb)
Dimensions	Modicon X80 standard single-slot module form factor
Operating Temp	0 to 60 deg C
Power Consumption	~1.5 W
Input Channels	8 isolated channels
Supported Voltage Ranges	0-10 V, +/-10 V, +/-5 V, 1-5 V
Supported Current Ranges	0-20 mA, 4-20 mA, +/-20 mA
Resolution	14 bits
Conversion Time	~1 ms per channel
Input Impedance	1 MOhm (voltage mode), 250 Ohm (current mode)
Measurement Accuracy	+/-0.3% of full scale
Overvoltage Protection	+/-30 V (voltage mode), +/-30 mA (current mode)
Isolation Breakdown	Channel-to-bus and channel-to-ground isolation layers
Local Diagnostics	Front panel status LEDs for module health and loop verification

Deterministic Network Routing and Backplane Scaling

The analog interface module executes real-time data conversion while maintaining structural data alignment with the underlying backplane bus communication velocity constraints. The processed 14-bit digital registers match standard hardware profiles, rendering variables immediately accessible across upper-level Profinet / EtherNet/IP deterministic networks. This design facilitates multi-channel I/O density scaling routines within the Modicon X80 architecture, maintaining stable sampling intervals and direct firmware flash compatibility across complex processing drops.

Frequently Asked Questions

Q: How does the internal protection framework respond when a field loop experiences an electrical fault exceeding nominal specifications?

A: The module incorporates input clamp circuits providing continuous overvoltage protection up to +/-30 V in voltage mode and overcurrent containment up to +/-30 mA in current mode. Field anomalies outside these boundaries trigger the channel-level diagnostic status bits, activate the local red fault LED indicator, and report the hardware exception block over the backplane bus.

Q: Is this specific analog input module hot-swappable during runtime execution of the control rack?

A: Yes, the Modicon X80 mechanical architecture permits removal and insertion under power (RIUP) operations. Field technicians can extract the card or decouple the terminal block assembly without disrupting the host CPU or degrading communications to adjacent hardware racks.

Q: Can single-ended voltage links and active current loops be run together on a single card?

A: Yes, individual channel parameter blocks allow mixed configuration choices across the 8 physical paths. Software variables dictate the internal signal trace layout to select either the 1 MOhm voltage path or the 250 Ohm current shunt resistor loop per channel point.

Field Installation Guidelines

Seat the module base into the selected slot on the Modicon X80 backplane chassis, pivoting the assembly until the upper retaining latch engages onto the metal rail. Fasten all lock screws to secure complete grounding path contact through the rear chassis plane. Maintain open air ventilation clearance corridors above and below the module rack to handle thermal dissipation and avoid exceeding the 0 to 60 deg C internal operating limit.

All sensor links must use shielded, twisted-pair cables sized to match the terminal assembly specifications. Route low-voltage measurement lines through dedicated, enclosed wire trays isolated from high-current AC main circuits or non-shielded variable speed drive lines. Terminate the overall copper shielding braid at a single, low-impedance grounding strip located at the entry panel base plate.

What's clients say about us

Excellent Emergency Support!

Our production line was down due to a faulty Bently Nevada monitor. We found it in stock here and they shipped it via DHL immediately. Back in operation within 48 hours—truly a lifesaver for our plant.

Mark Thompson

Maintenance Manager, USA

Reliable Source for New Spares

Finding brand new, original modules is critical for our safety. This team delivers factory-fresh components with full certification. Their commitment to only selling new products makes them our most trusted partner.

Robert Hoffmann

Engineering Lead, Germany

Top-tier Service and Quality

We have sourced Honeywell and Schneider parts here for two years. Every shipment arrives well-packaged with original factory seals intact. Clear communication and the best lead times in the industry.