IC693MDL754 GE Fanuc Series 90-30 Datasheet & Technical Manual

GE Fanuc IC693MDL754 Series 90-30 Digital Output Module

GE Fanuc IC693MDL754 Series 90-30 Digital Output Module

Availability: 10 left in stock

Configured for 12/24 VDC discrete switching in Series 90-30 PLC and PACSystem RX3i setups, the GE Fanuc IC693MDL754 (IC693MDL754 Digital...

SKU: IC693MDL754

Manufacturer: GE Fanuc
Product No.: IC693MDL754
Product Type: Digital Output Modules
Product Origin: USA
Payment:T/T, Western Union
Weight: 230g
Shipping port: Xiamen
Warranty: 12 months

Description Reviews

Configured for 12/24 VDC discrete switching in Series 90-30 PLC and PACSystem RX3i setups, the GE Fanuc IC693MDL754 (IC693MDL754 Digital Output Module) provides direct physical/electrical execution.

Hardware Specifications

Parameter	Specification
Model	IC693MDL754
Brand	GE Fanuc Emerson
Origin	United States
Weight	0.50 lbs (0.23 kg)
Dimensions	Single-slot Series 90-30 I/O form factor
Operating Temp	0 to 60 deg C (32 to 140 deg F)
Power Consumption	300 mA at 5 VDC (backplane bus)
Rated Output Voltage	12 to 24 VDC (operates up to 30 VDC)
Output Points	32 points (sourcing / positive logic)
Isolation Groups	2 isolated groups (16 points per common)
Output Current	0.75 A maximum per point
Steady-State Overcurrent Trip	5 A per point typical
Inrush Current	3 A without ESCP trip
Circuit Protection	Electronic Short-Circuit Protection (ESCP) per point
Hardware Configuration	Dual rear DIP switches
Fault Diagnostics	Overcurrent, short-circuit, loss of field power, ESCP failure, DIP switch mismatch

Firmware Flash Compatibility and High-Density Logic Scanning

The IC693MDL754 features firmware flash compatibility across Series 90-30 CPUs and PACSystems RX3i controllers. Its 32-point high-density output layout is logically mapped into two distinct isolated groups, optimizing field wiring efficiency while maintaining high backplane bus communication velocity. Onboard hardware diagnostic routines process Electronic Short-Circuit Protection (ESCP) events, missing field voltage, and hardware DIP switch setup mismatches, pushing fault interrupts to the primary CPU within a single scan cycle.

Frequently Asked Questions

Q: What happens if an output point on the IC693MDL754 experiences a short circuit or overcurrent condition?

A: The onboard Electronic Short-Circuit Protection (ESCP) trips at a typical steady-state threshold of 5 A, isolating the affected output point and transmitting a diagnostic fault signal directly to the CPU.

Q: Are the rear DIP switch settings required to match the software configuration?

A: Yes. The dual DIP switches located on the back of the module must strictly match the software module configuration in the programming environment to prevent hardware configuration error fault alerts.

Q: What thermal derating restrictions apply when operating at higher DC field voltages?

A: No thermal derating is required when operating at 24 VDC up to 60 deg C. However, when operating at field voltages up to 30 VDC, output current must be derated for ambient operating temperatures exceeding 40 deg C (104 deg F).

Field Installation Guidelines

Disconnect main power to the PLC rack chassis and turn off all external 12/24 VDC field power supplies before inserting or removing the module.
Verify that the dual DIP switches on the rear circuit board are set correctly to match the system software hardware configuration before installation into the rack baseplate.
Seat the module into the targeted I/O slot, pivoting the top hook into the backplate slot and pushing the bottom until the latch locks into position.
Wire field output loads to the removable terminal block, ensuring positive voltage is connected to the common terminal for each 16-point group in a positive logic (sourcing) arrangement.
Secure field wiring cables with proper strain relief and maintain separation from high-voltage AC cables to minimize electromagnetic interference.

What's clients say about us

Excellent Emergency Support!

Our production line was down due to a faulty Bently Nevada monitor. We found it in stock here and they shipped it via DHL immediately. Back in operation within 48 hours—truly a lifesaver for our plant.

Mark Thompson

Maintenance Manager, USA

Reliable Source for New Spares

Finding brand new, original modules is critical for our safety. This team delivers factory-fresh components with full certification. Their commitment to only selling new products makes them our most trusted partner.

Robert Hoffmann

Engineering Lead, Germany

Top-tier Service and Quality

We have sourced Honeywell and Schneider parts here for two years. Every shipment arrives well-packaged with original factory seals intact. Clear communication and the best lead times in the industry.